Bedienungsanleitung Extraflame SERAFINA EVO (Seite 19 von 36) (Englisch)

811801

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

19ENGLISH

OPERATION AND LOGIC

DO NOT USE ANY FLAMMABLE LIQUIDS FOR IGNITION!

DO NOT ALLOW THE BAG OF PELLETS TO COME INTO CONTACT WITH THE BOILING HOT STOVE DURING THE

FILLING PHASE!

IN THE EVENT OF CONTINUED FAILURE TO LIGHT, CONTACT AN AUTHORISED TECHNICIAN.

IGNITION

Once the previously listed points have been checked, press key 1 for three seconds to ignite the stove. During ignition, the stove will check for

a ame for a period of 15 minutes. When the right temperature is reached, the stove will switch from ignition to PREPARATION.

PREPARATION

During the preparation phase, the stove stabilises combustion, increasing it progressively, to then start ventilation and switch to WORK

WORK

In the work phase, the stove switches to the Set Power dened by the user, heating the room until Set Thermostat is achieved. See next

heading.

SET THERMOSTAT

The ambient Set thermostat can be set using keys 4 and 5, from LOWTA - 7°C - 37°C - HOT. If the value is between 7°C - 37°C, the stove checks

the room temperature using a probe on the machine. Once the set temperature has been reached, the stove automatically reduces the power,

guaranteeing best comfort and reducing pellet consumption: this process is called “modulation”.

LOWTA / HOT

If the Set Thermostat is "LOWTA" (set under the 7°C threshold), temperature checking is entrusted to the additional thermostat contact, thus

bypassing the on-board temperature probe.

If the contact is closed (request), the stove works at the set power.

If the contact is open (fullled), the stove works at minimum power.

If the setting is on “HOT” (set above 37°C), the stove only works at the set power, thus bypassing the external contact and the temperature

probe.

SET POWER

Set Power has 5 operating levels. The power can be changed with keys 2 or 3.

Power 1 = minimum level - Power 5 = maximum level.

Press key 1 to exit and save the change.

AUTO BLOW

During the work phase, the stove cleans the burn pot at regular intervals with an "AUTO BLOW".

When this procedure starts, a message is displayed. During the "AUTO BLOW" procedure, the pellet feed slow down and the fumes motor

increases.

After cleaning, the stove resumes operation in normal conditions.

SWITCHOFF

Press key 1 for three seconds.

Once this operation has been performed, the appliance automatically enters the switch-o phase, blocking the supply of pellets.

The ue gas exhaust motor and the hot air ow motor will remain on until the stove temperature has dropped below the safety settings.

REIGNITION

The stove can only be re-ignited if the temperature of the exhaust fumes is lower than the preset threshold and the minimum safety time has

passed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame SERAFINA EVO Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame SERAFINA EVO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info