Bedienungsanleitung Extraflame Virna Idro (Seite 23 von 40) (Englisch)

696240

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH

EASY SETUP

The volumetric weight of the pellet is the ratio between the weight and the volume of the pellet. This ratio may change while keeping the

quality of the pellet unchanged. By using the EASY SETUP function, it is possible to change the calibration of the volumetric weight by

increasing or decreasing the pre-set values.

In the stove program, the available values go from “– 3” to “+ 3”; all stoves are calibrated during production with the optimal value which is 0

If you notice an excessive deposit on the burning pot, access the EASY SETUP program and lower the value to “- 1”; then wait until the next

day and if there is no improvement, decrease again, to a maximum of “- 3”.

Instead, if it is necessary to increase the calibration of the volumetric weight of the pellet, go from the factory value “0” to “+ 1, + 2, + 3” as

required.

EXCESSIVE PELLET DEPOSIT IN THE BURNING POT NORMAL OPERATION MINIMUM PELLET DEPOSIT IN THE BURNING POT

-3 -2 -1 0 +1 +2 +3

THIRD

DECREASE

RANGE IF THE

FIRST TWO ARE

NOT ENOUGH

SECOND

DECREASE

RANGE IF THE

FIRST IS NOT

ENOUGH

FIRST DECREASE

RANGE (TEST

FOR 1 DAY)

OPTIMAL FACTORY

VALUE

FIRST INCREASE

RANGE

SECOND

INCREASE

RANGE IF THE

FIRST IS NOT

ENOUGH

THIRD INCREASE

RANGE IF THE

FIRST TWO ARE

NOT ENOUGH

CONTROLS PROCEDURE

 Press key 6.

 Press key 3 until EASY SETUP appears and conrm by pressing key 6.

 Use keys 4 and 5 to set the range.

 Press key 6 to conrm and key 1 to return to the previous menus to the initial state.

N.B.: IF THIS CALIBRATION DOES NOT SOLVE THE PELLET DEPOSIT IN THE BURN POT, PLEASE CONTACT YOUR LOCAL

AFTERSALES CENTRE.

CHRONO

This function allows the stove's ignition and switch-o to be automatically programmed.

The factory setting for CHRONO is o.

The chrono allows the programming of 4 time slots within a day, which can be used every day of the week.

Ignition and switch-o times can be set for each time slot, along with the specic days of application for the programmed time slot,

the desired temperature and power setting.

Current day and time settings are essential for the correct operation of the Chrono.

Recommendations

Before using the chrono function, you must set the current day and time, so check that you have followed the points listed in the

sub-chapter “DATETIME”. To use the chrono function correctly, you must activate it as well as program it. The four time slots can be

overlapped using the time switch on and o settings, This allows you to obtain a combination of times in which you can set dierent

temperatures and power without inuencing the stove work status.

NB: if overlapping time slots are set, the stove will stay on until the latest switch-o time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame Virna Idro Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame Virna Idro

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info