Bedienungsanleitung FAAC 455 (Seite 7 von 28) (Englisch)

119529

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

MANUAL RELEASE MECHANISM

The Manual Release mechanism is a built-in release

device of the 412 Operator (see Figure 4). To access the

keyhole, remove the plug on the top of the motor

housing. Then insert the key and turn it a half turn in

the direction of the gate’s closing to disengage the

operator’s motorized operation. You can now move the

gate leaf by hand to open or close the gate. Operating

the gate leaf by hand is necessary during installation

and is useful during power failures.

NSTALLING THE OPERATOR

Once you have prepared the gate, you are ready to

proceed with the installation of the operator.

Follow the instructions below to install your operator

whether in an inward or outward swinging

configuration.

Installing the operator consists of the following steps:

∗ Establishing the orientation of each gate leaf and its

operator.

∗ Attaching the rear mounting bracket

∗ Attaching the operator to the rear mounting bracket

∗ Attaching the front mounting bracket to the

operator

Page 7

January, 2004

412 Operator And

455 D Control Panel Installation Manual

Figure 4. Use the Manual Release key to disengage the

412 Operator from its motor so that you can move the

gate leaf by hand in the opening or closing direction

∗ Attaching the front mounting bracket to the gate

leaf

∗ Attaching the operator’s protective cover

∗ Installing the 455 D control panel

∗ Adjusting the torque for the operator

∗ Setting the operating controls

ESTABLISH THE ORIENTATION OF THE

PERATOR AND THE GATE LEAF

Before you begin mounting brackets or attaching parts,

you first need to establish the proper orientation of

each operator in relation to its gate leaf.

Figure 2 (page 5) shows a biparting gate from the side

where the operators are mounted. The operator

attached to the hinge on the left of the gate must be an

SX model. If the hinge is on the right side, the DX

model must be installed.

Installing the operator on the wrong side makes it

impossible to install the protective cover of the

operator.

ATTACH THE REAR MOUNTING

RACKET

Inward swinging gate:

You need to determine whether to attach the rear

mounting bracket directly to the post (or wall) or to

notch the post and install a recessed liner. Large pillars

require a recessed liner to house the rear mounting

bracket and part of the operator so that the pillar will

not interfere with the swing of the gate when it is fully

opened.

To determine whether you need a recessed liner,

measure the distances B and D (shown in Fig. 5) on your

gate. If your measure of B or D is greater than the

dimensions shown for your operator in Figure 5, notch

the post and construct a recessed liner for the post

mounting bracket (see Figure 6). The recessed liner

should be constructed of 3/16 or 1/4 in. steel with a

minimum interior height of 11 13/16 in. (30 cm) so as

to allow you to meet the required dimensions shown in

Figure 5. Make sure the recessed liner is securely

embedded in the post (or wall).

There are two parts to the rear mounting bracket. The

horizontal bracket attaches to the operator, and the

slotted vertical plate attaches to the gate post (see

Figure 8). Weld the two parts together and bolt the

assembly to the gate post of column. Note, though, that

use of the vertical rear mounting plate is optional.

Once you have positioned the rear mounting bracket,

attach the bracket to the post (or wall or recessed liner),

making sure the dimensions on your gate system match

those shown in Figure 5.

Figure 3.

Positive Stops

Remove the plug

on the top of the

motor housing

Insert the Manual Release

key and turn it in the

direction of the gate’s

closing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

FAAC 455 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von FAAC 455

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info