Bedienungsanleitung FAAC C850 (Seite 4 von 40) (Englisch)

560694

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

C850 532015 Rev. A

ENGLISH

1) ATTENTION! To ensure the safety of people, it is important that

you read all the following instructions. Incorrect installation or

incorrect use of the product could cause serious harm to people.

2) Carefully read the instructions before beginning to install the product.

3) Do not leave packing materials (plastic, polystyrene, etc.) within

reach of children as such materials are potential sources of danger.

4) Store these instructions for future reference.

5) This product was designed and built strictly for the use indicated in

this documentation. Any other use, not expressly indicated here,

could compromise the good condition/operation of the product and/

or be a source of danger.

6) FAAC declines all liability caused by improper use or use other than

that for which the automated system was intended.

7) Do not install the equipment in an explosive atmosphere: the presence

of inammable gas or fumes is a serious danger to safety.

8) The mechanical parts must conform to the provisions of Standards

EN 12604 and EN 12605.

For non-EU countries, to obtain an adequate level of safety, the

Standards mentioned above must be observed, in addition to national

legal regulations.

9) FAAC is not responsible for failure to observe Good Technique in

the construction of the closing elements to be motorised, or for any

deformation that may occur during use.

10) The installation must conform to current Directives and Standards

EN 12453 and EN 12445.

For non-EU countries, to obtain an adequate level of safety, the

Standards mentioned above must be observed, in addition to national

legal regulations.

11) Before attempting any job on the system, cut out electrical power.

12) The mains power supply of the automated system must be tted

with an all-pole switch with contact opening distance of 3 mm or

greater. Use of a 6A thermal breaker with all-pole circuit break is

recommended.

13) Make sure that a differential switch with threshold of 0.03 A is tted

upstream of the system.

14) Make sure that the earthing system is perfectly constructed and

connect metal parts of the closure to it.

15) The automated system is supplied with an intrinsic anti-crushing

safety device consisting of a torque control. Nevertheless, its tripping

threshold must be checked as specied in the Standards indicated

at point 10.

16) The safety devices (EN 12978 standard) protect any danger areas

against mechanical movement Risks, such as crushing, dragging,

and shearing.

17) Use of at least one indicator-light (e.g. FAACLIGHT ) is recommended

for every system, as well as a warning sign adequately secured to the

frame structure, in addition to the devices mentioned at point “16”.

18) FAAC declines all liability as concerns safety and efcient operation

of the automated system, if system components not produced by

FAAC are used.

19) For maintenance, strictly use original parts by FAAC.

20) Do not in any way modify the components of the automated system.

21) The installer shall supply all information concerning manual operation

of the system in case of an emergency and shall hand over to the

user the warnings handbook supplied with the product.

22) Do not allow children or adults to stay near the product while it is

operating.

23) Keep remote controls or other pulse generators away from children,

to prevent the automated system from being activated involuntarily.

24) Transit is permitted only when the automated system is idle.

25) The user must not attempt any kind of repair or direct action whatever

and contact qualied personnel only.

26) Check at least every 6 months the efciency of the system, particularly

the efciency of the safety devices (including, where foreseen, the

operator thrust force) and of the release devices.

27) Anythingnotexpresslyspeciedintheseinstructionsisnot

permitted.

WARNINGS FOR THE INSTALLER

GENERAL SAFETY REGULATIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

FAAC C850 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info