Bedienungsanleitung Faber 450 (Seite 13 von 40) (Englisch)

695385

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Installation Instructions

3.4 Terminals

The combined supply and discharge can be done both via wall or

through the roof or through an existing chimney. Verify if the

position of the terminal meets the local regulations regarding

ventilation openings.

The ue outlet can end on an external wall or a roof. Check

whether the outlet desired by you complies with local requirements

concerning good function and ventilation systems.

> Please note:

For a proper functioning the terminal should be at least 0,5m. away

from:

• Corners of the building

• Roof overhangs and balconies

• Eaves (with the exception of the roof ridge, see Chapter 15)

3.4.1 C11, wall terminal

For a facade or wall outlet use a wall terminal (see g. 1.9 C11).

Depending on the calculation this can be a diameter of

130/200mm or 100/150mm.

3.4.2 C31, roof terminal

For a at or pits roof outlet use a long roof outlet with a diameter of

100/150mm (see g. 1.9 C31).

3.4.3 C91, existing chimney

For an existing chimney use the short chimney outlet with a

diameter of 100/150mm (see g. 1.9 C91).

In this case the existing chimney acts as air inlet an inserted exible

stainless steel pipe discharges the ue gas. The top and the bottom

should be airtight.

Depending on the calculated outlet diameter, use a exible

stainless steel tube of Ø100mm or Ø130mm with CE marking

for 600°C.

> Please note:

The minimum chimney diameter for a 130mm exible stainless

steel pipe must 200x200mm. and for a 100mm exible stainless

steel pipe 150x150mm.

3.5 Existing chimney

You can also connect to an existing replace chimney. The existing

chimney functions then as air supply and a exible stainless steel

tube drawn through the chimney carries the ue gases. The exible

stainless steel tube of Ø100mm must have a CE mark have up to

600°C.

The chimney must have the following conditions:

• The channel of the chimney must be at least 150x150mm.

• There should be no more than one device on a chimney.

• The chimney must be in good condition:

- no leakage

- well cleaned

For more information about connections to existing chimneys, ask

the installation manual “chimney connection set”.

4 Preparation and installation

instructions

4.1 Gas connection

The gas connection must comply with the applicable local

standards.

We advise using a Ø 15mm gas connection directly from the gas

meter to the appliance, with a shut-off valve in the proximity of the

appliance, which must always be freely accessible.

Position the gas connection so that it is easily accessible at all

times for service, and that the burner unit can be disassembled.

4.2 Electrical connection

The power supply must comply with the applicable local standards.

A wall socket 230VAC/50Hz must be installed near the re.

For power supply make use of the included plug adapter.

See g 2.8 or 2.9 for the wiring diagram of this connection and the

LED Symbio module.

A = plug adapter

B = control unit

C = receiver

D = LED Symbio module

E = control block

F = magnet valve

G = 2nd thermocouple

4.2.1 Smart-Home installation

You can connect the control unit to the receiver with an external

source, such as a Domotica home automation system, using the

5-wire pin connector.

(Part G60-ZCE/1000, art.no.: 06022950). The total length of the

cable may not exceed 8m. Signal relay (gold-plated contacts) or

opto-couples are recommended!

4.2.2 Faber ITC (Intelligent Technical Controller)

The ITC gives you more options, such as ECO control, control,

error messages, maintenance advice and such.

For further information see the ”ITC” user manual.

4.3 Preparing the re

• Remove the re from its packaging. Ensure that the gas

supply pipes under the appliance are not damaged.

• Remove frame and glass and take the packaged parts from

the re.

• Store frame and glass in a safe place.

• Prepare the gas connection on the regulator.

4.4 Positioning the re

Take the installation requirements into account (see Chapter 3).

Place the appliance in the right position and set the height with the

(optional) leg levelers.

Height adjustment and levelling of the appliance (see point C, g.

1.1).

Rough height adjustment:

• With the extendable (optional) leg.

Fine adjustment:

• With the adjustable feet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber 450 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Faber 450

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info