Bedienungsanleitung Faber 800 (Seite 15 von 44) (Englisch)

695386

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Installation Instructions Installation Instructions

4.4.1 Hanging on the wall 800/500-650-IIL, -IIR and -III

The appliance can be wall-mounted with the optional wall bracket

(see g. 1.8).

4.5 Installing the ue materials

• When penetrating a non-combustible wall or ceiling the

opening must be at least 5mm larger than the diameter of the

discharge material. At a combustible wall or ceiling is this

100mm larger than the diameter of the drainage material.

• Horizontal sections should be installed with a slope towards

the re (3 degrees).

• Build the system from the re. If this is not possible you can

make use of an extendable adapter section.

• For truing up the exhaust system use the 0,5m. pipe, which

can be shortened and ensure that the inner pipe is always

2cm longer than the outer pipe.

• Parts, which are shortened, must be secured with a

self-tapping screw.

• Wall and roof terminals can also be cut.

• Do not insulate but ventilate built-in ue material (approx.

100cm²).

4.6 Constructing the false chimney

If possible, carry out a performance test at the re before nally

nishing the installation.

4.6.1 False chimney

* Construct the false chimney of non-combustible material in

combination with metal proles or of masonry/concrete

blocks.

* Be aware of ventilation grids and service door (see g. 1.0 to

1.5). Place above the ventilation grids a screen plate made of

non-combustible material (see g. 1.1, 1.3 or 1.5)

* Always use a lintel or reinforcing bars while bricking the

outlet. They should not be placed directly on the re.

* Built the false chimney against the appliance (see g. 1.0 to

1.5). Keep a minimum distance of 2mm between the false

chimney and the appliance, because of the extension of the

appliance.

4.6.2 Installation and nishing

For installation and nishing the following points are of interest:

H = moldings (g. 2.4 and 2.7)

I = distance prole (g. 2.4)

J = upper side ange combustion chamber (g. 2.5)

K = distance holder/glass support (g. 2.6)

L = distance holder/glass support (g. 2.6)

> Please note:

Ensure that the re is not load-bearing with regard to the false

chimney breast.

4.6.3 Method I with cover strip (g. 2.2)

Build the false chimney breast or plateau against the moldings H

and distance proles I (see g. 2.4 and 2.7).

Keep a minimum distance of 2mm between the false chimney and

the appliance, because of the extension of the appliance. Take into

account the thickness of the nish!

4.6.4 Method II with built-in strip (g. 2.3)

Remove the distance proles “I” (see g. 2.4).

Make sure that the screws of the front distance prole “I” will be

replaced, in order to ensure the air tightness of the appliance.

Build the plateau against the glass supports K and L (see g. 2.6).

Keep a minimum distance of 2mm because of the extension of the

appliance.

For the height of the plateau see point “J” (g. 2.5).

5 Removing the glass

5.1 Removing the glass from the front

MatriX 800-I:

• Remove the moldings “A” left and right (g. 3.0).

• Turn the left and right side clamps “B” up (g. 3.0).

• Place the suction cups on the glass and slide the upper list

“C” up (g. 3.1).

• See g. 3.2, number:

1. Slide the glass to the top so that the bottom will

release.

2. Now, carefully slide the glass to the left.

3. Get the released side towards to you and put the glass

on a safe place.

MatriX 800-II:

• Remove molding “A” left or right (g. 3.0).

• Turn the left or right side clamps “B” up (g. 3.0).

• Place the suction cups on the glass and slide the upper list

“C” up (g. 3.3).

• See g. 3.3, number:

1. Slide the glass to the top so that the bottom will

release.

2. Now, carefully slide the glass to the left or to the right.

3. Get the released side towards to you and put the glass

on a safe place.

MatriX 800-III:

• Place the suction cups on the glass and slide the upper list

“C” up (g. 3.3).

• See g. 3.3, number:

1. Slide the glass to the top so that the bottom will

release.

4. Get the released side towards to you and put the glass

on a safe place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber 800 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Faber 800

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info