Bedienungsanleitung Faber Agio 24WH (Seite 6 von 13) (Englisch, Französisch)

752941

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

Version 7/11 - Page 6

6. Reattach the control box and support. Make sure that

the wiring harness is concealed behind the support.

7. Remove the eld wiring compartment cover. Feed the

Power Supply Cable through the electrical knockout.

8. Attach the backdraft damper to the proper exhaust open-

ing using two silver screws supplied with the rangehood.

 Attach the rangehood to the cabinet bottom. The four

key holes slip onto the four screws mounted to the cabinet

bottom. Tighten the screws.

 Connect the Power Supply Cable to the rangehood.

Attach the White lead of the power supply to the White lead

of the rangehood with a twist-on type wire connector. Attach

the Black lead of the power supply to the Black lead of the

rangehood with a twist-on type wire connector. Connect

the Green (Green and Yellow) ground wire under the Green

grounding screw.

4. Remove the central support and control box by remov-

ing the screws indicated in FIGURE 11. It is not necessary

to remove the blower to perform this operation.

5. Attach the cover behind the exhaust grate with two silver

screws supplied with the rangehood as indicated in FIGURE 12.

11. Replace the eld wiring compartment cover. For duct-

less installations, refer to the next section which discusses

ductless installations. Replace the grease lters.

12. Turn the power supply on. Turn on blower and light.

IF THE RANGEHOOD DOES NOT OPERATE:

• Check that the circuit breaker is not tripped or the

house fuse blown.

• Disconnect the power supply and check that the

wiring connections have been made properly.

DUCTLESS INSTALLATIONS

For ductless installations, the blower must be positioned with

the exhaust pointing forward ( so that the exhaust exits from

the front grill ) before attaching the rangehood to the cabinet.

Ductless installations require Charcoal Filters.

1. Remove both grease lters, the central support and the

control box. Remove the two thumb screws on either side of

the blower and remove the blower from the mounting guides

as indicated in FIGURE 11.

2. 

.

Then Rotate the blower 180° so that the exhaust points out

the front of the rangehood. Replace the black lter holders

and the two thumb screws and tighten so that the blower

is securely fastened inside the rangehood as indicated in

. Reattach the control box and central support.

Make sure that the wiring harness is concealed behind the

central support.

 For ductless installations, Charcoal Filters are required

and must be installed before the grease lters are replaced.

The charcoal lters attach to both ends of the blower as

indicated in FIGURE 14.



FIGURE 11

FIGURE 12

FIGURE 14



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber Agio 24WH Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info