Bedienungsanleitung Faber Arkea (Seite 5 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

753235

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

Controls

Button Function Led

LTurns the lights on/off at maximum strength. -

T1 Turns the motor on/off at speed one. Fixed.

Keeping the button pressed for approximately 2 seconds starts/stops the temperature

sensor.

1ashofLEDsT2

and T3 algorithm

activated.

2 ashes of LEDs

T2 and T3 algorithm

deactivated.

T2 Turns the Motor on at speed two.

Press and hold the button for approximately 5 seconds, with all the loads

turned off (Motor and Lights), to turn the Activated Charcoal Filter alarm on. The

relevant LED ashes twice to conrm.

To turn the alarm off, press the button again and hold for at least 5 seconds.

The relevant LED ashes once.

Fixed.

T3 Turns the Motor on at speed three.

Press and hold the button for approximately 3 seconds, with all the loads turned

off (Motor and Lights), to perform a reset. The LED S1 ashes three times.

Fixed.

T4 Turns the Motor on at INTENSIVE Speed.

This speed is timed to run for 6 minutes. At the end of this time, the system

returns automatically to the speed that was set before. If it is activated with the

motor turned off, the hood will switch to OFF at the end of the time.

Press and hold for 5 seconds to enable the remote control, indicated by the

LED ashing twice.

Press and hold for 5 seconds to disable the remote control, indicated by the

LED ashing just once.

Fixed.

S1 Signals the Metal Grease Filter saturation alarm, indicating that it is necessary

to wash the lters. The alarm is triggered after the Hood has been in operation

for 100 working hours.

Fixed.

When this is activated, it signals the Activated Charcoal Filter saturation alarm,

indicating that the lter must be changed; the Metal Grease Filters must also

be washed. The Activated Charcoal Filter saturation alarm comes into operation

after the Hood has been working for 200 hours.

Flashing.

WARNING: the temperature sensor is active when the hood is started. If, when the hood is off, the tempe-

rature detected by the sensor exceeds the set limit, the hood will turn on at speed two. When the tempe-

rature detected by the sensor returns below the threshold value the hood will turn off. In the event of the

temperature not returning below the threshold value for approximately 90 minutes, the hood will turn off (the

sensor is disabled for approximately 15 minutes, after which it will return to the previous setting). If the hood

is adjusted manually (switching on/changing speed) the sensor is disabled and the hood must be turned off.

After turning the hood off, the sensor is disabled for approximately 15 minutes, after which it will return to

the previous setting. The temperature sensor does not guarantee automatic start-up of the hood, as its

operation is inuenced by environmental conditions, types of cooking operation, height and installation of

the hood (tested at 530 mm).

WARNING: the sensor does not work with induction cookers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber Arkea Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info