Bedienungsanleitung Faber Classica (Seite 6 von 16) (Englisch, Französisch)

752956

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Version 05/10- Page 6

- ” min

15 3/4 ” max

18 1/4”

10 3/4”

36”

also consult cooktop

manufacturer's recommendation

upper

chimney

lower

chimney

canopy

x = distance from hood to cooktop

(varies depending on installation)

min - 24”, suggested max - 30”

cabinet base

FIGURE 4

19 3/4”

PREPARE THE WALL

1. Disconnect and move freestanding range from cabinet

opening to provide easier access to upper cabinet and rear

wall. Put a thick, protective covering over cooktop, set-in

range or countertop to protect from damage or dirt.

2. Determine and mark the centerline on the wall where the

range hood will be installed. Based on the ceiling or sofﬁt

height, determine the distance 24" min, 30" max needed

(FIGURE 4) between the cooking surface (E in FIGURE

5) and the bottom of the rangehood. To this distance,

add 11 3⁄8" (B in FIGURE 5) and draw a horizontal line

(A in FIGURE 5) about 24" long centered on the vertical

centerline (D in FIGURE 5) at this distance.

3. Mark 2 points on each side of the (B) horizontal line 3½"

from the vertical centerline ( C in FIGURE 6). Drill 2 holes

for installation, the screws provided are for mounting the

range hood into wood; mounting into drywall or plaster is not

recommended. Install the 2 mounting screws, leave a

¹⁄₄" gap between the wall and the back of the screw

head to slide the range hood into place.

INSTALLATION DIMENSIONS

The Classica chimneys are adjustable and designed to meet varying ceiling

heights as indicated in FIGURE 4. The chimneys can be adjusted for ceil-

ings between 7' 5" and 9' 2 3/4" depending on the distance between the

bottom of the hood and the cooktop (distance x in FIGURE 4).

FIGURE 5

For shorter ceilings,

have the chimney

cover(s) cut at a sheet

metal shop. For higher

ceiling installations, the

High Ceiling Chimney

Kit includes a new 39”

upper chimney which

would replace the 15

3/4” upper chimney that

came with the hood.

min & max ceiling height examples

x = 30"

min

7' 11"

max

9' 2 3/4"

x = 28"

min

7' 9"

max

9' 3/4"

x = 26"

min

7' 7"

max

8' 10 3/4"

x = 24"

min

7' 5"

max

8' 8 3/4"

Note: for ductless installations, subtract 3 1/2" from the minimum

ceiling height

FIGURE 6

4. Place one of the chimney brackets against the wall so

that its top edge is 1/16" (C) from the ceiling or sofﬁt and

level. Align the center notches (B) of the bracket and the

centerline (A). Mark the centers of the bracket holes and

attach to the wall with 2 screws. (see FIGURE 7)

5. Place the other chimney bracket on the wall so that its

lower edge is 16 1/16" from the ceiling or sofﬁt and level.

Align the center notches of the bracket and the centerline.

Mark the centers of the bracket holes. Attach to the wall

with 2 screws (FIGURE 8)

FIGURE 7

FIGURE 8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber Classica Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info