Bedienungsanleitung Faber Farum (Seite 42 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Norwegisch)

525643

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

41 < < < <

6.3.4 Existing chimney

You can also connect the appliance to an

existing chimney. The existing chimney will

function as an air supply and a flexible

stainless steel pipe drawn up through the

chimney will remove the combustion gas.

The flexible stainless steel pipe of Ø 100 mm

should have a CE mark for temperatures up to

600° Celsius.

The chimney should comply with the following

requirements:

 The diameter of the flue system

must be at least 150x150 mm.

 There should be no more than 1

appliance connected to a flue pipe.

 The chimney must be in good

condition

o No leakage and

o It should be properly swept.

For more information about connections to

existing flue systems, see the manual

“connections”.

6.4 Preparation and Installation

instructions

6.4.1 Gas connection

The gas connection must comply with locally

valid standards.

We advise Pipe work from the meter to the

appliance must be of adequate size., with

near the appliance a gas isolater tap that

should always be accessible. Place the gas

connection in such a way that this is easily

accessible, and that before service, the

burner unit can be disconnected at all times.

6.4.2 Electric connection

If an adapter is used for the power supply,

then a wall socket 230VAC – 50Hz must be

mounted in the close neighbourhood of the

hearth.

6.4.3 Preparation of the appliance

 Remove the packaging of the

appliance . Make sure the gas pipes

underneath the appliance are not

damaged.

 Clear a safe space to store the frame

and the glass.

 Remove the frame , (if necessary) and

the glass and take the separately

wrapped parts out of the appliance

 Prepare the gas connection to the gas

control valve.

6.4.4 Placing the appliance

Take the installation requirements into

account (see chapter 3 )

6.4.5 Mounting the smoke emission

outlet materials

 In case of a wall or roof terminal, the

hole must be at least 5 mm bigger

than the diameter of the flue

material.

 Horizontal parts must be installed at a

(3 degree) slope up away the

appliance.

 Build up the system from the

appliance. If this is not possible, you

should make use of a adjustable pipe

 For fitting the system a ½ metre

cut-down pipe should be used. Make

sure the inner pipe is always 2 cm

longer than the outer pipe. Wall and

roof terminal are also shortened.

These parts must be secured with a

self tapping screw.

 Do not insulate but ventilate build-in

flue material (approx.100cm2)

6.5 Removing the glass

 Place the suction discs onto the

glass

 Remove the cover strips on

theleft and right hand side. (see

fig. 2.1.)

 Remove the glass clips, by using a

screwdriver. (see fig. 2.2.)

 Slide the glass upwards so that

the bottom edge is released. Now

gradually move the bottom edge

of the glass forwards and lower

the glass ( see fig.2.3 )

To replace the glass repeat the process in

reverse order.

Remove all fingerprints from the glass,

these will be burned into it once the

appliance is used.

6.6 Placing the decorative material

It is not allowed to add different or more

materials to the combustion chamber.

Always keep the pilot burner free from

decorative material!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber Farum Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info