Bedienungsanleitung Faber Look (Seite 11 von 116) (Deutsch, Englisch, Dänisch, Französisch, Spanisch, Türkisch, Norwegisch)

753223

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

EN 1

USE

Control panel

Button Function Led

A Motor off. The Leds indicating the Speed of the motor turn off.

Enables / Disables Keyboard Lock mode if pressed

and held for 5 seconds. All the Leds light up in cycle and run a start-up sequence.

B Activates speed one. The Leds indicating Speed one and Motor Off turn on.

C Activates speed two. The Leds indicating Speed two and Motor Off turn on.

D Activates speed three. The Leds indicating Speed three and Motor Off turn on.

Press and hold the button for approximately 5

seconds, with all the loads turned off (Motor and

Lights), to turn the Activated Charcoal Filter alarm

on.

To turn it off, press and hold the button again for 5

seconds.

Button A LED flashes twice.

Button A LED flashes once.

E Activates speed four. The Leds indicating Speed four and Motor Off turn on.

Press and hold for 5 sec. to activate Intensive

speed. This speed is timed to run for 6 minutes. At

the end of this time the system will return to the

speed set previously.

It is disabled by pressing the Button or turning the

Motor off.

The Led flashes once a second and button A Led lights up.

F Starts the 24H function, in which the motor starts at

a speed that allows suction of 100 m3/h for 10

minutes per hour. This mode cannot be activated if

Intensive or Delay modes are active.

To deactivate it, press the same button or button A.

The Leds indicating 24H speed and Motor Off turn on.

24H Led Flashing:

Indicates the need to wash the metal grease filters. The alarm is

triggered after the Hood has been in operation for 100 working

hours.

When the filters alarm is triggered, the alarm can be

reset by pressing and holding this button for

approximately 5 seconds. These indications are

only visible when the motor is turned off.

The button A Led flashes three times

G Activates Delay mode, causing automatic

shutdown of the Motor and the Lighting system

with a 20’ delay.

It is disabled by pressing the button or turning the

motor off.

The Delay and Motor Off button Leds turn on.

Delay Led Flashing:

Indicates the need to change the activated charcoal filters, and

also to wash the metal grease filters. The alarm is triggered after

the Hood has been in operation for 200 working hours.

Pressing and holding the button for 5 seconds

enables the remote control.

Pressing and holding the button for 5 seconds

disables the remote control

Button A Led flashes twice.

Button A Led flashes once.

H Press briefly to turn the lighting system on and off

at maximum intensity. The Led on the button lights up.

Press and hold the button for 2 seconds to turn the

Courtesy Lights On (if provided). The Led on the button lights up.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber Look Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Faber Look

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info