Bedienungsanleitung Faber MATRIX 1050-400 II (Seite 13 von 48) (Englisch)

696328

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Installation Instructions Installation Instructions

1 Dear user

Congratulations on purchasing your Faber product, a quality

product that will provide you with the warmth and atmosphere for

many years. Please read the user manual before using the re.

Should a malfunction occur despite the careful nal checks, then

you can always contact your Faber dealer.

Please note:

The data of your re is available in the user manual.

1.1 Introduction

Only have the appliance installed by a qualied installer according

to the gas safety regulations.

Read this installation manual properly.

1.2 Please check

Check the re for transport damage and report any damage

immediately to your dealer.

1.3 CE Declaration

Glen Dimplex Benelux certies that this Faber re complies with the

essential requirements of the gas appliances directive.

Product: gas room heater

Model: MatriX 1050/500-I/IIL/IIR/III, MatriX 1050/650-I/IIL/IIR/III

Applicable EC directives: 90/396/EEC

Harmonized standards applied: NEN EN 613:2000 and NEN EN

613/A1:2003

This declaration is invalid, if without the written permission of Glen

Dimplex Benelux:

• Changes are made to the appliance.

• The re is connected to other exhaust materials than

specied.

2 Safety instructions

• The unit must be installed and subsequently serviced every

year and maintained in accordance with these instructions

and the applicable national and local regulations.

• Ensure that the data on the type label matches the local gas

type and pressure.

• The settings and the construction of the re must not be

changed!

• Do not place extra imitation wood or other smoldering

material on the burner or in the combustion chamber.

• The appliance is for atmosphere and heating purposes. This

means that all surfaces, including the glass, can be very hot

(over 100°C). Exceptions to this are the bottom of the re

and the control elements.

• Do not place any combustible materials within 0,5m of the

radiation area of the re.

• Through the natural air circulation of the re moisture and

uncured volatile components from paint, building materials

and carpeted oors, etc. are attracted. These parts can settle

as soot on cold surfaces. Therefore do not light the re

shortly after installation.

• Light the re for the rst time and run for several hours on the

highest setting, so that the paint can cure. Provide adequate

ventilation, so that any fumes can disperse; we recommend

vacating the room during this process.

> Please note:

1. All transport packaging is removed.

2. No children and pets in the room present.

3 Installation requirements

3.1 Fire

• This device can be built into an existing or new chimney.

• For devices with exible gas pipes, the gas regulator block is

mounted on the right side of the re for transport reason (g

1.6). The gas regulator block with the receiver and the I.T.C.

must be placed on a distance of max. 30cm behind a service

door.

When desired, there are 2 metres burner pipes

(To prevent damage to cables and pipes during transport,

these are tied together with tie-wraps.

Remove it to ensure the proper functioning of the appliance).

3.2 False chimney breast or other structure

• The false chimney should be of non-combustible material.

• The space above the re should always be ventilated using

the supplied grids or a similar alternative with minimal free

passage of 200cm² per grid.

• The false chimney breast and its construction may not rest on

the appliance.

• It is not permitted to start directly on the device with

concentric cut down pipe material.

The air supply could then possibly be closed.

3.3 Flue pipe and terminal requirements

• For the supply of the combustion air and the discharge of the

combustion gases you should always use the Flue materials

specied by Faber. Only when using these materials can

Faber guarantee the safe and proper operation of the

appliance.

• The outside of the concentric ue material can heat up to

+/-150°C. Ensure, when penetrating a ammable wall or

ceiling, construction with proper insulation and protection.

And ensure respective distance.

• Ensure for great discharge lengths that the concentric

discharge material is supported every 2m, so that the weight

of the material is not supported by the re.

• It is not permitted to start directly on the device with

concentric cut down pipe material.

The air supply could then possibly be closed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber MATRIX 1050-400 II Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Faber MATRIX 1050-400 II

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info