Bedienungsanleitung Faber MATRIX 800-650 I (Seite 17 von 44) (Englisch)

695398

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Installation Instructions Installation Instructions

8 Instructions for client

• Recommend that the unit should be checked annually by a

qualied specialist to ensure the safe use and to guarantee a

long service life.

• Give advice and instructions on care and cleaning of the

glass. Highlight the danger of burnt-in ngerprints.

• Instruct the customer on the operation of the appliance and

the remote control, including setting the receiver.

• Hand over to customer:

- installation manual

- user manual

- log set instruction card

- suction cups

9 Annual maintenance

9.1 Checking and cleaning:

* Check and clean if necessary after verication:

- the pilot light

- the combustion chamber

- the glass

- the logs for breakage

- the outlet

* Replace, if necessary:

- chips/glass granulate

9.2 Cleaning the glass

Most deposits can be removed with a dry cloth. Clean the glass

with a ceramic hob cleaner.

> Please note:

Avoid ngerprints on the glass. These are no longer removable

after they are burnt in!

Now carry out check-up as described in Chapter 7 “Checking after

installation”.

10 Conversion to other gas type

The conversion to a different gas type may only be performed by a

qualied installer/dealer.

10.1 Conversion from natural gas to propane

(or vice versa)

This can only be done by replacing the burner. To do so, please

contact your dealer.

Specify with your order always the type and serial number of the

device.

11 Flue calculation

A simple way to calculate whether the exhaust conguration is

possible in combination with your re, use the free “Faber Flue App”

and download it from:

INTERNET:

BlackBerry, Android, PC (with Google Chrome browser)

APP store:

iPhone, iPad and Mac.

Google Play:

Android smartphones and Android tablets.

Alternatively use the exhaust calculation table (see chapter 13).

The alternatives of outlet lengths and any restrictors are set out in

the restrictor table. In the table we work with start length (STL), total

vertical height (TVH) and total horizontal length (THL).

• Start length (STL):

This is the rst part that is placed on the re and represents a

certain value (g. 12.1, 12.2 and 12.3 A, N and F). This value is in

the top row of the table (see restrictor table 11.1 and 11.2).

• Total vertical height (TVH):

TVH is the difference in height measured from the top of the unit to

the outlet; it can be measured or determined from the building plan.

For clarication see the TVH indication in the drawings (g. 12.1,

12.2 and 12.3).

• Total horizontal length (THL):

THL is the total horizontal length and consists of elbows and pipes

which are entirely in the horizontal plane. Elbows I, K and Q and

the elements H, J, L, M, P and R (g. 12.1 and 12.2).

• Length horizontal plane:

The horizontal length consists of the elements H, J, L, M, P and R

(g. 12.1 and 12.2).

• Elbows 90° in the horizontal plane:

Horizontal bends are bends which are entirely in the horizontal

plane (g. 12.1, 12.2 and 12.3 I, K and Q).

• Bends 45° or 30° in the horizontal plane:

Horizontal bends are bends which are entirely in the horizontal

plane.

• Elbows 90° vertical to horizontal plane:

These are 90° elbows, which proceed from horizontal to vertical

(g. 12.2 and 12.3 G, O and S).

• Bends 45° or 30 °vertical to horizontal plane:

These are 30° or 45° bends with a vertical offset of less than 45°

(g.12.1 B and D).

• Pipes under a tilt angle:

These are pipes which are vertically ascending at an angle of 30°

or 45° (g. 12.1 C). Fill in only in combination with at least 2x 30 or

45° bends in the vertical part.

• Restrictor table:

See the restrictor table at the right vertical (TVH) and horizontal

length (THL).

For “x” and if the values are outside the table, then the combination

is not allowed. Only then adjust the TVH or THL.

If a value is indicated, check that the calculated STL value is not

lower than indicated in the table. In this case STL must be adjusted.

The found value indicates the width of the restrictor (“0” means no

restrictor). Standard is a restrictor of 30mm installed (see g, 2.0 F,

rst remove hatch “G”).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber MATRIX 800-650 I Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Faber MATRIX 800-650 I

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info