Bedienungsanleitung Faber MATRIX 800-650 III (Seite 16 von 44) (Englisch)

695740

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Installation Instructions Installation Instructions

5.2 Removing the glass from the side

It is not necessary to take out the glass from the side to place the

log set or for maintenance.

MatriX 800-II en -III:

• First, remove the front glass (see Chapter 5.1).

• Remove the left or right clamp strip on the top (g. 3.4).

• Place the suction cups on the glass (g. 3.5).

• See g. 3.5, number:

1. Slide the glass towards to you and to the top so the

bottom and back side will release.

2. Now, carefully get the underside towards to you and

put the glass on a safe place.

> Please note:

Replace the glass in reverse order.

Clean all ngerprints on the glass; otherwise they will burn in once

the re is used.

6 Placing the decoration material

It is not permitted to use other or to add more material in the

combustion chamber.

Keep the pilot light always free of decoration material!

See g. 4.0 to 4.5 or the included log set card:

• Divide the glass granulate on the perforated bottom plate.

• Place the 2 large wood blocks and make sure there is no

glass granulate underneath.

• Place the other wood blocks.

• Divide the chips on the glass granulate and the perforated

bottom plate.

• Start the re as described in the user manual.

• Assess whether the ame distribution and the Symbio-effect

is good. Move or remove any chips/glass granulate to a good

Symbio-effect.

• Replace the glass (Chapter 5) and check the re image.

7 Checking the installation

7.1 Checking the main burner ignition, pilot ame

Ignite the re as described in the user manual.

• Check that the pilot ame is well above the main burner and

not covered by chips.

• Check the ignition of the main burner on full and small

setting. (Ignition must be smooth and quiet).

7.2 Checking for gas leaks

Check with a gas leak nder or spray all connections and pipes for

gas leakage.

7.3 Checking the burner pressure and primary

pressure

Check that the burner pressure and primary pressure match with

the information listed in the manual, Chapter 14 “Technical

specications”.

Measuring the primary pressure:

• Close the shut-off valve.

• Turn measuring nipple B (see g. 1.7) some turns open and

connect a measuring hose to the gas regulator.

• Take this measurement at highest setting of the re and when

the re is set to pilot light.

• Do not connect the unit if the pressure is too high.

Measuring the burner pressure:

Check the burner pressure only with proper primary pressure.

• Turn measuring nipple A (see g. 1.7) some turns open and

connect a measuring hose to the gas regulator.

• The pressure must correspond to the value indicated in the

technical specications of this manual. In case of deviation contact

the manufacturer.

> Please note:

Close all pressure measuring nipples and check for gas leakage.

7.4 Checking the ame image

Let the re burn for at least 20 minutes at highest setting and check

the ame for:

* Flame distribution

* Color of the ames

If one or both points are not acceptable then check:

• The log set layout and/or the amount of glass granulate/chips

on the bottom plate.

• The pipe connections for leaks (in case of blue ames).

• Whether the correct ue restrictor is tted. (see g, 2.0 F, rst

remove hatch “G”).

• The outlet.

- Wall terminal right side up

- Roof terminal on the right position

- If the maximum horizontal ue lengths is not exceeded.

7.5 Flue gas analyzer

If you are in possession of a CO/CO2 ue gas analyzer, then it is

possible to check the supply air and the combustion gases.

There are two measuring pipes at the front of the re between the

mounting frame and the glass (g. 2.1).

The ratio CO2 and CO must not be greater than 1:100.

Example:

CO2 is 4% and CO is 400ppm, measured at the highest point.

If the ratio is greater than 1:100 or exhaust gases are measured in

the supply air, then also check above points.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber MATRIX 800-650 III Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Faber MATRIX 800-650 III

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info