Bedienungsanleitung Falcon 1092 CT Dual Fuel (Seite 24 von 36) (Englisch)

500342

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Conversion to LP

If the appliance is to be converted to LP gas do the

conversion at this point. See the conversion section of

these instructions.

Levelling

You are recommended to use a spirit level on a shelf in

one of the ovens to check for level.

Place the cooker in its intended position taking care not

to twist it within the gap between the kitchen units as

damage may occur to the cooker or the units.

The rollers can be adjusted to level the cooker. To adjust

the height of the rear of the cooker use the levelling tool

supplied to turn the adjusting nuts at the front bottom

corners of the cooker.

Adjust the height of the front roller to level the cooker.

Turn clockwise to raise the cooker and anticlockwise to

lower.

When you are satisﬁ ed with the height and level raise the

front of the cooker by one turn of the front roller adjuster.

Screw down the front feet to meet the ﬂ oor. Screw the

front roller adjuster anticlockwise to raise the front roller

so that the front of the cooker is supported on the feet,

not the front roller, to prevent accidental movement of

the cooker.

Gas Connection

Fitting a stability bracket

A stability bracket or chain (not supplied by with the

cooker) should be ﬁ tted when the cooker is connected

to a ﬂ exible gas supply. Any restraining device should be

secured to the fabric of the building and should be able

to be released so that the cooker can be pulled out for

cleaning and maintenance.

When ﬁ tting a stability bracket read these instructions

together with the leaﬂ et supplied with the bracket.

a) Position and level the appliance.

b) Draw a pencil line 68mm from the front edge of the

levelling feet.

c) Mark oﬀ 300mm from the RH side of the unit to

indicate the centre line for the bracket.

d) Remove the unit.

e) Mark oﬀ 595mm to locate the front edge of the lower

bracket. Fix bracket to ﬂ oor.

f) Measure the height from ﬂ oor level to the top edge

of the rear channel. Add 3mm to this dimension and

assemble the stability bracket to this height (i.e. from

ﬂ oor level to underside of top member)

Gas Connection

The Gas supply needs to terminate with a down facing

bayonet. The rear cover boxes limit the position of the

supply point.

view from the rear

A position for gas supply connector

B appliance gas inlet

Because the height of the cooker can be adjusted and

each connection is diﬀ erent it is diﬃ cult to give precise

dimensions. Ideally the house supply bayonet should

be in the shaded area shown in the diagram. Although

a 900mm hose can be used, a 1250mm hose will allow

slightly more ﬂ exibility in the positioning of the bayonet

and make moving the cooker easier. The hose should be

ﬁ tted so that both inlet and outlet connections are vertical

so that the hose hangs downwards.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falcon 1092 CT Dual Fuel Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info