Bedienungsanleitung Falcon 1092 CT Dual Fuel (Seite 30 von 36) (Englisch)

500342

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

SERVICING  WARNING

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.

Servicing

1 Servicing

When servicing or replacing gas carrying components,

disconnect from the gas supply before commencing

operation.

Check the appliance is gas sound after completion of

service. When checking for gas leaks do not use washing

up liquid - this can corrode. Use a product speciﬁ cally

manufactured for leak detection.

Do not use re-conditioned or unauthorised gas controls.

Disconnect from the electricity supply before

commencing servicing, particularly before removing any

of the following: - control panel, side panels, hotplate tray

or any electrical components or covers.

Before electrical re-connection, check that the appliance

is electrically safe.

Note - References to LH and RH oven apply as viewed

from the front.

BEFORE SERVICING ANY GAS CARRYING COMPONENTS.

TURN OFF THE GAS SUPPLY.

2 To Remove the Hotplate

Disconnect the appliance from the electricity supply. Pull

the unit forward to gain access.

a) Remove the French cooktop/pan supports/hotplate

accessories and burner caps.

b) Remove the brass venturi in the centre of each

hotplate burner bezel.

c) Remove the bezel from the hotplate and disconnect

the spark ignition lead from the spark electrode.

d) Lift the hotplate clear of the appliance.

e) Replace in reverse order.

3 To Remove the Control Panel

Disconnect the appliance from the electricity supply.

a) Remove the pan supports/hotplate accessories and

burner caps.

b) Slacken the brass venturi at the centre of each burner.

c) Remove the control knobs from all taps.

d) Open the grill and RH oven doors. Remove 3 ﬁ xings

on the top front and 3 ﬁ xings on the control panel

underside.

e) Pull the control panel forward. Remove the

connections from the rear of the three neons.

Disconnect the earth lead and lift the panel clear of

the unit.

f) Replace all parts in reverse order.

g) When replacing any electrical connections refer to the

wiring diagram.

4 To Remove an Outer Side Panel

Disconnect the appliance from the electricity supply.

a) Remove the control panel as detailed in Section 3

b) Remove the retaining screw on the upper front edge

and the two ﬁ xings on the rear or the side panel. Undo

the lower retaining screw situated below the edge at

the panel front corner.

c) Remove the panel by pulling it away from the unit.

Should diﬃ culty be encountered, it may be necessary

to slacken the two closest burners and both brass

venturi as detailed in Section 2.

d) Replace parts in reverse order. Ensure that both

venturis are fully tightened.

5 To Remove an Oven or Grill Neon

Disconnect the appliance from the electricity supply.

a) Remove the control panel as detailed in Section 3

b) Remove the relevant neon connection and undo the

nut which secures the neon to the control panel.

c) Replace parts in reverse order. Ensure the replacement

neon functions correctly.

6 To Remove a Thermostat

Disconnect the appliance from the electricity supply.

a) Remove the hotplate as detailed in Section 2.

b) Remove the control panel as detailed in Section 3

c) Open the appropriate oven door and remove the oven

shelves.

d) Pull the unit forward to gain access to the cover box.

Undo the cover screws and lift clear.

RH oven

Remove the two ﬁ xings that secure the thermostat

phial cover. Unclip the thermostat phial from the clips

in the oven back panel.

LH oven

Remove the two screws holding the thermostat phial

to the oven fan cover at the rear of the oven. Pull the

unit forward to access the rear of the cooker. Remove

the both cover boxes by removing the ﬁ xing screws

and lifting clear. Feed the thermostat capillary clear of

the oven.

e) Disconnect the wires from the thermostat and undo

the two ﬁ xings which secure the control to the

mounting plate.

f) Fit the replacement and re-assemble in reverse order.

Ensure that the phial is clipped to the oven rear,

positioned centrally between the clips. Check that the

thermostat functions correctly.

7 To Replace a Grill Controller

Disconnect the appliance from the electricity supply.

a) Remove the hotplate as detailed in Section 2.

b) Remove the control panel as detailed in Section 3.

c) Disconnect the controller wiring. Undo the ﬁ xings that

secure the device to the mounting plate.

d) Fit the replacement and re-assemble parts in reverse

order. Check that the replacement functions correctly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falcon 1092 CT Dual Fuel Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info