Bedienungsanleitung Falcon De Luxe 1000DF (Seite 18 von 56) (Englisch, Französisch)

500343

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

English

a) Position and level the appliance.

b) Draw a pencil line along the front edge of the

base of the cooker and along the right hand edge.

c) Remove the range.

d) Mark off 570mm from the RH side of the unit to

indicate the centre line for the bracket.

e) Mark off 415mm to locate the front edge of the

lower bracket. Fix bracket to ﬂ oor.

f) Measure the height from ﬂ oor level to the bottom

of the opening in the cooker back. Add 3mm to

this dimension and assemble the stability bracket

to this height (i.e. from ﬂ oor level to underside of

top member)

Gas Connection

The Gas supply needs to terminate with a down facing

bayonet. The rear cover boxes limit the position of the

supply point.

view from the rear

Because the height of the cooker can be adjusted and

each connection is different it is difﬁ cult to give precise

dimensions. Ideally the house supply bayonet should

be in the shaded area shown in the diagram. The hose

should be ﬁ tted so that both inlet and outlet connections

are vertical so that the hose hangs downwards in a ‘U’

shape. A 3ft (915mm) hose will need to be connected

from the side

For Natural Gas the ﬂ exible hose must be in accordance

with B.S.669.

For LP Gas it should be capable of 50mbar pressure,

70C temperature rise and carry a red stripe, band or

label.

If in doubt contact, your supplier.

Screw connect the threaded end of the hose into the gas

inlet in the underside of the connector block on the back

of the cooker.

After completing the gas connection, check the cooker

is gas sound with a pressure test. When checking

for gas leaks do not use washing up liquid - this can

corrode. Use a product speciﬁ cally manufactured for leak

detection.

Pressure testing

The gas pressure can be measured at the pressure test

point on the gas connection block.

Connect the pressure gauge. Turn on and light one of

the hotplate burners.

For Natural Gas the pressure should be 20mbar.

For Propane the pressure should be 37mbar.

Electrical Connection

This appliance must be installed by a qualiﬁ ed

electrician to comply with the relevant regulations and

also the local electricity supply company requirements.

WARNING: THIS APPLIANCE MUST BE EARTHED

Note

The cooker must be connected to the correct electrical

supply as stated on the voltage label on the cooker,

through a suitable cooker control unit incorporating

a double pole switch having a contact separation of

at least 3mm in all poles. This cooker must not be

connected to an ordinary domestic power point.

The total electrical load of the appliance is approximately

8.8kW. The cable size used should be suitable for this

load and comply with all local requirements.

Access to the mains terminal is gained by removing the

electrical terminal cover box on the back panel.

Connect the mains cable to the correct terminals for your

electrical supply type.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falcon De Luxe 1000DF Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info