Bedienungsanleitung Falcon Toledo 90 (Seite 28 von 40) (Englisch)

659394

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

ArtNo.132-0003 - Single-phase connections (AUS)

A N

Electrical Connection

This appliance must be installed by a qualied electrician

to comply with the relevant regulations (AS/NZS

60335.2.6) and also the local electricity supply company

requirements.

Make sure that the mains characteristics (voltage, nominal,

power, etc.) match the ratings indicated on the data plate

axed to the cooker.

Current Operated Earth Leakage Breakers

The combined use of your cooker and other domestic

appliances may casue nuisance tripping, so we

recommend that the cooker is proctected on an individual

RCD (Residual Current Device) or RCBO (Residual Current

Breaker with Overload)

IF IN DOUBT, PLEASE CONTACT A SUITABLY QUALIFIED

ELECTRICIAN.

The cooker is preset for a single-phase earthed electrical

connection. It is essential to install a multi-pole circuit breaker

that completely disconnects the appliance from the mains,

with a minimum contact break distance of 3 mm.



WARNING: THIS APPLIANCE MUST BE EARTHED.

The appliance must be connected to an ecient earthing

circuit. If the electricity network is not equipped with an

earth connection, then it must be installed separately in

compliance with local regulations.

Earthing is a safety measure required by law, and must be

performed with particular care by a qualied technician,

who must also check that the electricity supply

characteristics are correct.

The total electrical load of the appliance is approximately

7.4 kW. The cable size used should be suitable for this load

and comply with all local requirements.

Access to the mains terminal is gained by removing the

electrical terminal cover box on the back panel. Connect

the mains cable to the correct terminals for your electrical

supply type (Fig.7-10 and Fig.7-11). Check that the links are

correctly tted and that the terminal screws are tight. Secure

the mains cable using the cable clamp.

Fixed Wiring

For connection to xed wiring, i.e. exible conduit, remove

the electrical terminal cover box on the back panel. Using the

two screws, x the strain relief bracket in position.

Fix the conduit-to-conduit mounting bracket onto the

strain relief bracket. Connect the mains cable to the correct

terminals for your electrical supply type (Fig.7-12 and

Fig.7-13). Check that the links are correctly tted and that the

terminal screws are tight.

Replace the electric terminal cover box; make sure that the

conduit is clear of the bottom ange.

ArtNo.132-0005 - Fixed wiring connection 2 (AUS)

Mains terminal

Fixing bracket for

conduit connection

Conduit

Cable clamp

A N

Fig.7-13

ArtNo.132-0002 - 3 phase 240/415Vac 50Hz

3-phase 400-415 V

50 Hz

Fig.7-12

3-phase 230 V 50 Hz

ArtNo.132-0001 - 1 phase 240Vac 50Hz

1-phase 220-240 V

50 Hz

Fig.7-10

Fig.7-11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falcon Toledo 90 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info