Bedienungsanleitung Falcon Toledo XT 110 (Seite 48 von 60) (Englisch, Französisch)

500344

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

WARNING  SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.

Conversion to another gas

Check in the Technical Data section at

the back of the book that the cooker is

convertible to the gas you want to use.

This conversion must be performed by a competent person.

After conversion the installation must comply with the

relevant regulations and also the local electricity supply

company requirements. Read the instructions before

converting this appliance.

Failure to convert the appliance correctly could invalidate

any warranty or liability claims and lead to prosecution.

This instruction must be used in conjunction with the rest

of the appliance in struc tion, in particular for information on

Standards, cooker positioning, connection hose suitability

etc.

When servicing or replacing gas-carrying components

disconnect from gas before commencing operation and

check appliance is gas sound after completion.

Do not use re-conditioned or unauthorised gas controls.

Disconnect from the electricity supply before commencing

servicing. Before electrical re-connection, check that the

appliance is electrically safe.

Injectors

Remove burner caps and heads. Remove old jets. Fit the

new jets. See the Technical Data section at back of the book

for the correct jets. Reassemble in reverse order.

Tap adjustment

Disconnect from electricity supply.

Open the oven doors and remove the ﬁ xing screws

underneath the control panel. NB some models have a plate

under the facia held in place by the bottom ﬁ xing screws.

Pull oﬀ all the control knobs.

Slide the control panel to the right and then pull forward.

Take care not to damage or strain the wiring.

Lift the control panel, pull forward.

Take care not to damage or strain the wiring.

To convert to another gas.

Unscrew the tap bypass screw.

Using a pair of long nose pliers carefully remove the bypass

screw and ﬁ t the correct replacement screw. See the

Technical Data section at back of the book for the correct

size. Tighten the screw down.

Reﬁ t the control panel.

Stick on label

Stick the appropriate label on to the data badge to indicate

the gas the appliance is now set for.

Pressure Testing

Connect the appliance to the gas supply. Check the

appliance is gas sound.

See Technical data section at the back of this book for test

pressures.

The gas pressure can be measured at one of the left hand

hotplate burner jets. Lift oﬀ a burner head. Fit the pressure

gauge to the jet. Turn on the hotplate burner and turn on

and light one of the other burners.

After checking the pressure, turn the taps oﬀ and replace

the burner head.

Reassemble burner top, making sure it is reassembled in the

correct way on the burner body.

Check the appliance is gas sound.

Check operation of all the burners.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falcon Toledo XT 110 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info