Bedienungsanleitung Falmec Alphabet Island (Seite 21 von 72) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

661993

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

English

are completely dry before repositioning them. To remove and replace these filters, see

the instructions in point H1. This operation should be performed at regular intervals.

2. CHARCOAL FILTERS

These trap the odours present in the stream of air that passes through them. The air is puri-

fied by passing a number of times through the filters and being recirculated into the kitchen.

The charcoal filters cannot be cleaned, and should be replaced on average every 3-4 months

(according to use). To replace the charcoal filters, see the instructions in point H2.

3. CLEANING THE OUTSIDE OF THE APPLIANCE

It is advised to clean the external hood surfaces at least every 15 days in order to avoid that

oily or greasy substances affect the steel surfaces.

The ouside of the range hhod should be cleaned using a damp cloth and neutral liquid

detergent or denatured alcohol.

In case of fingerprint-less finish (fasteel) clean only with water and neutral soap using

clean with a soft cloth, rinse and wipe dry thoroughly. Do not use products that contain

abrasive substances, rough cloths or cloths specifically designed for cleaning steel. Using

abrasive substances or rough cloths will inevitably damage the finish of steel. The steel

surface will be irrevocably damaged if the instructions above are not complied with.

Keep these instructions together with the instructions for use of your hood.

The manufacturer accepts no liability for any damage caused by non-compliance with the

instructions above.

4. CLEANING THE INSIDE OF THE APPLIANCE

The electrical parts or parts of the motor assembly inside the range hood must not be

cleaned using liquids or solvents.

Do not use abrasive products. All the above operations must be performed after having dis-

connected the appliance from the mains power supply.

WARRANTY

The new equipment is covered by warranty.

The warranty conditions are provided by the distributor.

The manufacturer is not liable for any inaccuracies in this booklet resulting from printing or

transcription errors. The manufacturer reserves the right to modify its products as it consid-

ers necessary or in the interests of the user, without compromising their essential safety and

operating characteristics.

HOOD INSTALLATION

WARNING: Failure to install the screws or fixing device in accordance with these instructions

may result in electrical hazards.

O1 - INSTRUCTIONS FOR WALL-MOUNTED MIRABILIA HOODS

Phase 1

- Place the support bar next to the wall (A-Fig. O1), at a height above the cooktop which cor-

responds to X+300 mm.

- With a spirit level check that the bar is horizontal. Mark a point at each end of the bar.

- Drill the holes, fit 2 ø8mm expansion joints and screw in the bar.

Phase 2

- Fit the hood to the support bar (Fig. O2).

- Adjust hood alignment with the relevant screws: The top screw (B) adjusts the distance from

the wall. The bottom screw (C) adjusts the vertical sliding movement.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falmec Alphabet Island Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info