Bedienungsanleitung Falmec Altair top Wall (Seite 14 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

661996

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ELECTRICAL CONNECTION

(only intended for qualied personnel)

Disconnect the equipment from electrical mains power supply before carry-

ing out any operations on the hood.

Ensure that the wires inside the hood are not disconnected or cut:

in the event of damage, contact your nearest Servicing Department.

Refer to qualied personnel for electrical connections.

Connection must be carried out in compliance with the provisions of law in force.

Before connecting the hood to the electrical mains power supply, check that:

 

hood;

 -

cations located inside the hood);

 -

ing 70 °C;

 

with regulations in force;



the socket used to connect the hood is within reach.

In case of:

 

The wires must be connected as follows: yellow-green for earthing, blue for neutral and

brown for the phase. The plug must be connected to an adequate safety socket.



xed equipment not provided with a power supply cable and plug, or any other device

that ensures disconnection from the electrical mains, with an opening gap of the con-

tacts that enables total disconnection in overvoltage category III conditions.

Said disconnection devices must be provided in the mains power supply in compliance

with installation regulations.

The yellow/green earth cable must not be cut o by the switch.

The Manufacturer declines all responsibility for failure to comply with the safety regulations.

FUMES DISCHARGE

EXTERNAL EXHAUST HOOD SUCTION

In this version the fumes and vapours are discharged outside through

the exhaust pipe.

To this end, the hood outlet tting must be connected via a pipe, to an

external output.

The outlet pipe must have:

 

 

owing back into the motor.

 

 

the hood.

You are required to insulate the pipes if it passes through cold environments.

In the presence of motors with 800m

/h or higher, a check valve is present to prevent

external air owing back.

Deviation for Germany:

when the kitchen hood is used at the same time as appliances that are powered by energy other

than electricity, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar).

HOOD WITH INTERNAL RECIRCULATION FILTERING

In this model, the air passes through the charcoal lters to be puried

and recycled in the environment.

Ensure that the active carbon lters are assembled into the hood, if not,

install them as indicated in the assembly instructions.

In this version the check valve must not be assembled: remove it if it is on the air

outlet tting of the motor.

ASSEMBLY INSTRUCTIONS

only intended for qualied personnel

The hood can be installed in various congurations.

The generic assembly steps apply to all installations; for each case, follow

the specic steps provided for the required installation.

OPERATION

WHEN TO TURN ON THE HOOD?

Switch on the hood at least one minute before starting to cook to direct fumes and vapours

towards the suction surface.

After cooking, leave the hood operating until complete extraction of all vapours and odours.

By means of the Timer function, it is possible to set auto switch-o function which will allow

the hood to turn o automatically after 15 minutes of operation.

WHICH SPEED IS TO BE SELECTED?

1st speed: maintains the circulation of clean air with low electricity consumption.

2nd speed: normal conditions of use.

3rd speed: presence of strong odours and vapours.

4th speed: rapid disposal of odours and vapours.

WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?

The metal lters must be cleaned every 30 hours of operation.

The active carbon lters must be replaced every 3-4 months, depending on the use of the

hood.

For further details see the “MAINTENANCE” chap.

ELECTRONIC PUSHBUTTON PANEL

Motor ON/OFF

Upon start-up, the speed is that stored at the previous operation.

Increase speed from 1 to 4

Speed 4 is only active for a few min-

utes, then speed 3 activates.

The speeds are indicated by the LEDs

on the keys:



Speed 1

Speed 2

Speed 3

only version:

Speed 4

("+" LED ashing)

Reduce speed from 4 to 1

Light on/o

TIMER (red LED ashing)

Auto switch-o after 15 min.

The function deactivates (red LED o) if:

- The TIMER key (

) is pressed again.

- The ON/OFF key (

) is pressed.

FILTER ALARM (red LED steady on with ( ) o)

Anti-grease lter maintenance after approximately 30 hours of operation.

Press (

) the meter for 3 seconds to reset.

800

600

Falmec Altair top Wall Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info