Bedienungsanleitung Falmec Blade Wall (Seite 20 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

662004

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

MAINTENANCE

Before cleaning or carrying out maintenance operations, disconnect the equipment by removing the plug or switching o the

main switch.

Regular maintenance guarantees proper operation and good performance over time.

Special attention is to be paid to the metal anti-grease lters and active carbon lters. In fact, frequent cleaning of the lters and their supports

ensures that no grease is accumulated on the hood, which is dangerous and can cause res.

EXTERNAL CLEANING

You are advised to clean the external surfaces of the hood at least once every 15 days to prevent oily substances and grease from sticking to them.

To clean the brushed stainless steel hood, the Manufacturer recommends using "Magic Steel" wipes. Alternatively, it can be cleaned using a damp

cloth, slightly moistened with neutral, liquid detergent or denatured alcohol. Finish o cleaning by rinsing well and drying with soft cloths.

Do not use too much water next to the push button control panel and lighting devices in order to prevent humidity from reach-

ing electronic parts. You must not use detergents containing abrasive, acid or corrosive substances or abrasive cloths: a direct

consequence of not complying with these warnings will result in irreversible deterioration of the hood's surface.

The glass panels can only be cleaned with specic, non-corrosive or non-abrasive detergents using a soft cloth.

The Manufacturer declines all responsibility for failure to comply with these instructions.

It is possible to remove the external suction panel completely in order to facilitate its cleaning (refer to the instructions G on page 6).

CLEANING OF INTERNAL PARTS

It is forbidden to clean electrical parts, or parts related to the motor inside the hood, with liquids or solvents.

Do not use abrasive products.

All these operations are to be carried out after having disconnected the equipment from the electrical mains power supply.

METAL ANTIGREASE FILTERS

The metal anti-grease lters are there to contain suspended grease particles: deposited on the lters, these feed on any

ames released when cooking, generate unpleasant odours, and compromise the passage of air, thus reducing suction

performance of the hood.

For this reason, it is advised to frequently wash the metal lters (at least once a month) leaving them to soak in boiling

water and dish washing liquid for 1 hour, taking care not to bend them. Do not use corrosive, acid or alkaline detergents.

Rinse them well and wait for them to be completely dry before reassembling them.

Washing in a dishwasher is permitted, however, it may cause the lter material to darken: to reduce the possibility of this

problem from happening, use low-temperature washes (55°C max.).

Open the external suction panel to remove the metal anti-grease lters (refer to the instructions G on page 6), then operate the handle

(refer to the instructions H on page 6). Carry out operations in reverse order to insert them.

ACTIVE CARBON FILTERS

Active carbon lters have the function of retaining odours in the air ow passing through them. The air, puried by running

many times through the lter, is recirculated into the kitchen.

Active carbon lters cannot be washed and are to be immediately replaced every 3-4 months (depending on the fre-

quency of use of the hood).

Dispose of the active carbon lters in compliance with the regulations in force in the country of use.

To replace the active carbon lters, open the external suction panel (refer to the instructions G on page 6),

remove the metal anti-grease lters (refer to the instructions H on page 6) and follow the instructions I on

page 6.

DISPOSAL AFTER END OF USEFUL LIFE

The crossed-out wheeled bin symbol on the appliance means that the product is WEEE, i.e. "waste electrical and electronic equipment", according-

ly it must not be thrown out with unsorted waste (i.e. with "mixed household waste"), but it must be disposed of separately so that it can undergo

specic operations for its re-use, or a specic treatment, to remove and safely dispose of any substances that may be harmful to the environment

and remove the raw materials that can be recycled. Correct disposal of this product contributes to saving precious resources and avoiding potential

negative eects on human health and the environment, which could be caused by inappropriate waste disposal. You are kindly asked to contact

your local authorities for further information regarding the designated waste collection points nearest to you. Penalties for improper disposal of such

waste can be applied in compliance with national regulations.

INFORMATION ON DISPOSAL IN EUROPEAN UNION COUNTRIES

The EU WEEE Directive was implemented dierently in each country, accordingly, if you wish to dispose of this appliance we suggest contacting

your local authorities or dealer to nd out what the correct method of disposal is.

INFORMATION ON DISPOSAL IN NONEUROPEAN UNION COUNTRIES

The crossed-out wheeled bin symbol is only valid in the European Union: if you wish to dispose of this appliance in other countries, we suggest

contacting your local authorities or dealer to nd out what the correct method of disposal is.

Falmec Blade Wall Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info