Bedienungsanleitung Falmec Dora (Seite 11 von 48) (Alle Sprachen)

709796

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

ENGLISH

ELECTRONIC PUSHBUTTON PANEL

Motor ON/OFF

Upon start-up, the speed is that stored at the previous operation.

Increase speed from 1 to 3

Speed 4 is only active for a few min-

utes, then speed 3 activates.

The speeds are indicated by the LEDs

on the keys:

Speed 1

Speed 2

Speed 3

Reduce speed from 3 to 1

Light on/o

TIMER (red LED ashing)

Auto switch-o after 15 min.

The function deactivates (red LED o) if:

- The TIMER key (

) is pressed again.

- The ON/OFF key (

) is pressed.

FILTER ALARM (red LED steady on with ( ) o)

Anti-grease lter maintenance after approximately 30 hours of operation.

Press (

) the meter for 3 seconds to reset.

MAINTENANCE

Before cleaning or carrying out maintenance operations, disconnect the

equipment by removing the plug or switching o the main switch.

Do not use detergents containing abrasive, acidic or corrosive substances

or abrasive cloths.

Regular maintenance guarantees proper operation and performance over time.

Special attention is to be paid to the metal anti-grease lters : frequent cleaning of the

lters and their supports ensures that no ammable grease is accumulated.

CLEANING OF EXTERNAL SURFACES

You are advised to clean the external surfaces of the hood at least once every 15 days

prevent oily substances and grease from sticking to them. To clean the brushed stainless

steel hood, the Manufacturer recommends using "Magic Steel" wipes.

Alternatively and for all the other types of surfaces, it can be cleaned using a damp cloth,

slightly moistened with mild, liquid detergent or denatured alcohol.

Complete cleaning by rinsing well and drying with soft cloths.

Do not use too much moisture or water around the push button control

panel and lighting devices in order to prevent humidity from reaching

electronic parts.

The glass panels can only be cleaned with specic, non-corrosive or non-abrasive deter-

gents using a soft cloth.

The Manufacturer declines all responsibility for failure to comply with these instructions.

CLEANING OF INTERNAL SURFACES

Do not clean electrical parts, or parts related to the motor inside the hood,

with liquids or solvents.

For the internal metal parts, see the previous paragraph.

METAL ANTI-GREASE FILTERS

It is advised to frequently wash the metal lters (at least once a month) leaving them to

soak in boiling water and cleaning solution for 1 hour, taking care not to bend them.

Do not use corrosive, acid or alkaline detergents.

Rinse them well and wait for them to be completely dry before reassembling them.

Washing in a dishwasher is permitted, however, it may cause the lter material to darken: to

reduce the possibility of this problem from happening, use low-temperature washes (55°C

max.).

To extract and insert the metal anti-grease lters see the assembly instructions.

ACTIVE CARBON FILTERS

These lters retain the odours in the air that passes through them. The puried air is recircu-

lated into the environment.

The active carbon lters must be replaced on average every 3-4 months under normal con-

ditions of use.

See assembly instructions to replace the active carbon lters.

LIGHTING

The range hood is equipped with high eciency, low consumption LED spotlights with an

extremely long life-span under normal use conditions.

Should the LED spotlight need to be replaced, proceed as shown in the gure.

DISPOSAL AFTER END OF USEFUL LIFE

The crossed-out trash or refuse bin symbol on the appliance means that the

product is WEEE, i.e. “Waste electrical and electronic equipment'', accordingly it

must not be disposed of with regular unsorted waste (i.e. with ''mixed house-

hold waste''), but it must be disposed of separately so that it can undergo specif-

ic processing for its re-use, or a specic treatment, to remove and safely dispose of any

substances that may be harmful to the environment and remove the raw materials that can

be recycled. Proper disposal of these products contributes to saving valuable resources and

avoid potential negative eects on personal health and the environment, which may be

caused by inappropriate disposal of waste.

You are kindly asked to contact your local authorities for further information regarding the

designated waste collection points nearest to you. Penalties for improper disposal of such

waste can be applied in compliance with national regulations.

INFORMATION ON DISPOSAL IN EUROPEAN UNION COUNTRIES

The EU WEEE Directive was implemented dierently in each country, accordingly, if you wish

to dispose of this appliance we suggest contacting your local authorities or dealer to nd

out what the correct method of disposal is.

INFORMATION ON DISPOSAL IN NONEUROPEAN UNION COUNTRIES

The crossed-out trash or refuse bin symbol is only valid in the European Union: if you wish

to dispose of this appliance in other countries, we suggest contacting your local authorities

or dealer to nd out what the correct method of disposal is.

WARNING!

The Manufacturer reserves the right to make changes to the equipment at any time and

without prior notice. Printing, translation and reproduction, even partial, of this manual are

bound by the Manufacturer's authorisation.

Technical information, graphic representations and specications in this manual are for in-

formation purposes and cannot be divulged.

This manual is written in Italian. The Manufacturer is not responsible for any transcription

or translation errors.

12V

Falmec Dora Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info