Bedienungsanleitung Falmec Ellittica - wall (Seite 27 von 88) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Alle Sprachen)

709781

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

- Locate the desired height between the hood and hob (see sect. C).

- Remove the back (A) by removing the cover caps (T) and loosen the inside fastening screws

(V1).

- Mark the 4 drilling points F, according to the dimensional specifications shown in the figure,

or use the back as a drilling template.

Fig. W03-W04

- Fasten the back (A) to the wall using the 4, Ø8 mm expansion plugs and the screws (V2)

provided.

- Check the horizontal and vertical alignment of the back with a spirit level.

Fig. W05-W06

- For the exhaust version, (define the upper and lower output use) locate the optimal length

of the fumes exhaust pipe (F) and connect. To facilitate the operation, if the ceiling height

allows it, cover B can be temporarily removed by acting on fastening screws. Carry out elec-

trical connections only after disconnecting the power supply. For the filter version, make

sure the exhaust on cover B is free to allow the air purified by carbon filters to be exhausted.

- Attach the hood to the back using the 4 hooks (G) ensuring the hood is down by approx 10

mm, to check its tightness.

Fig. W07-W08

- Tighten, but not completely, the two upper fastening screws (V1).

- Lift the hood to the desired position and tighten the upper and lower fastening screws com-

pletely (V1).

- Power the hood in accordance with applicable regulations (see sect. D of this booklet).

HOOD INSTALLATION WITH GLASS (optional fig. W09-W10-W11-W12-W13)

- Remove the metal filter using handle (C). Disconnect the hood from the mains.

- Disconnect connector (S) of the spotlights cable.

- Remove the body (A) from the cone (B+D) loosening the 4 M4 milled metric screws (V3).

- Slightly loosen the 2 centring and anti-rotation metric screws (V4) in the lower flange of the

cone (B), and centre the glass slot with the metric screws.

- Fasten the body (A) to the cone (B) with the 4 M4 milled metric screws (V3).

- Refit the metal filter using handle (M). Supply power in accordance with applicable regula-

tions (see sec. D of this booklet).

INSTALLATION INSTRUCTIONS FOR POLAR HOOD WITHOUT GLASS

PREDISPOSITION

ISLAND HOOD

Fig. 1-2

- Remove the fastening screws between the extension and trellis (only for transport).

- Fasten the top trellis (C) to the ceiling using the 6, 8 ø Fischer anchors and the screws

provided(V1).

Fig. 3-4

- Locate the desired height between the hood and the hob (see sect. C).

- Fasten the lower three-piece unit (chimney + extension +trellis, B+D+G) to the upper trellis

trellis (C).

- For the exhaust version, locate the optimal height of the fumes exhaust pipe, and connect.

For the filter version, the upper extension slots must remain free to allow the air purified by

carbon filters to be exhausted.

- Make electrical connections only after having disconnected the electric power supply.

Fig. 5

- Slide the extension (D) upwards under the upper flange of the trellis. Next, turn clockwise

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falmec Ellittica - wall Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info