Bedienungsanleitung Falmec Gruppo Incasso Green Tech (Seite 22 von 80) (Alle Sprachen)

709803

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

USING THE RADIO CONTROL

WARNINGS!:

Place the hood away from sources of electromagnetic waves (e.g.

microwave ovens), which could interfere with the radio control

and with the hood electronics.

The maximum operating distance is 5 metres, that may vary according to

the presence of electromagnetic interferences.

Radio control operated at 433.92MHz.

The radio control consists of two parts:

- the receiver built into the hood;

- the transmitter shown here in the gure.

DESCRIPTION OF TRANSMITTING COMMANDS

Motor switch-on and speed increase

from 1 to 4. Speed 4 is only active for a

few minutes.

DOWN

Speed decrease and motor switch-o.

Light ON-OFF

Short impulse:

turn light on and o

Long impulse:

change light tone from 2700K to 5600K

TIMER ON: The motor automatically

switches o after 15 min.

The function is automatically disabled if

the motor is switched o (

key)

Command transmission active

The radio control is optional for the GRUPPO INCASSO and Green Tech.

Follow the entire procedure described below if purchased.

Skip the activation procedure for IL GRUPPO INCASSO MURANO.

ACTIVATION PROCEDURE (for GRUPPO INCASSO and Green Tech)

Before using the radio control, follow the procedure below on the hood push-

button panel:

• Press LIGHT (

) and TIMER ( ) simultaneously until all LEDs start ashing.

• Release the two keys and press LIGHT ( ) again until all LEDs are lit up.

• Release LIGHT ( ): now the receiver is active.

This procedure is also used to deactivate the receiver.

RADIO CONTROL CODE CHANGE

With only one radio control, go directly to point 2.

With several radio controls in the same room, a new code can be created by

following the procedure below.

Disconnect the power to the hood before starting the procedure.

1  CREATE A NEW CODE

The procedure is to be carried out on the radio control.

• Press LIGHT and TIMER simultaneously until the display starts ashing.

• Press DOWN on the radio control: saving is conrmed by three brief ash-

es of the display. The new code cancels and replaces the previous default

code.

Reconnect the hood to the electrical power supply, making sure

that the lights and motor are o.

2A  ASSOCIATING THE RADIO CONTROL WITH THE HOOD

USING THE ELECTRONIC PUSHBUTTON PANEL

press TIMER ( ) on the hood pushbutton panel for 2 seconds:

the red LED lights up.

press any key on the radio control within 10 seconds.

2B  ASSOCIATING THE RADIO CONTROL WITH THE HOOD

USING THE TOUCH PUSHBUTTON PANEL

press LIGHT ( ) on the hood pushbutton panel for 2 seconds:

the red LED lights up.

press any key on the radio control within 10 seconds.

RESTORING DEFAULT CODE

the procedure is to be carried out if the hood is disposed of, sold or transferred.

Disconnect the power to the hood before starting the procedure.

• Press UP and DOWN simultaneously on the radio control for more

than 5 seconds: reset is conrmed by three brief ashes of the display.

• Reconnect the hood to the electrical power supply.

• Proceed with associating the hood and the radio control, as described in

point 2.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falmec Gruppo Incasso Green Tech Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info