Bedienungsanleitung Falmec Gruppo Incasso NRS (Seite 17 von 72) (Alle Sprachen)

709806

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH

The outlet pipe must have:

• a diameter not less than that of the hood ﬁtting.

• a slight slope downwards (drop) in the horizontal sections to prevent conden-

sation from ﬂowing back into the motor.

• the minimum required number of bends.

• the minimum required length to avoid vibrations and reduce the suction per-

formance of the hood.

You are required to insulate the pipes if it passes through cold environments.

In the presence of motors with 800m3/h or higher, a check valve is present to

prevent external air ﬂowing back.

Deviation for Germany:

when the kitchen hood is used at the same time as appliances that are powered by

energy other than electricity, the negative pressure in the room must not exceed 4 Pa

(4 x 10-5 bar).

HOOD WITH INTERNAL RECIRCULATION FILTERING OPTIONAL

In this model, air passes through the active carbon ﬁlters HP

(optional) to be puriﬁed and is then recycled into the environ-

ment. Ensure that the active carbon ﬁlters HP are assembled

into the hood, if not, install them as indicated in the assembly

instructions.

In this version the check valve must not be assembled: remove it if it is

on the air outlet ﬁtting of the motor.

ASSEMBLY INSTRUCTIONS

only intended for personnel qualied

WARNING: Make sure the suspended element has available front access.

The hood can be installed in various congurations.

The generic assembly steps apply to all installations; for each case,

follow the specic steps provided for the required installation.

OPERATION

WHEN TO TURN ON THE HOOD?

Switch on the hood at least one minute before starting to cook to direct fumes

and vapours towards the suction surface.

After cooking, leave the hood operating until complete extraction of all vapours

and odours. By means of the Timer function, it is possible to set auto switch-oﬀ

function which will allow the hood to turn oﬀ automatically after 15 minutes of

operation.

WHICH SPEED IS TO BE SELECTED?

1st speed: maintains the circulation of clean air with low electricity consump-

tion.

2nd speed: normal conditions of use.

3rd speed: presence of strong odours and vapours.

4th speed: rapid disposal of odours and vapours.

WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?

The metal ﬁlters must be cleaned every 30 hours of operation.

The HP active carbon ﬁlters (optional), must be reactivated every 3-4 months,

depending on the use of the hood.

For further details see the “MAINTENANCE” chap.

ELECTRONIC PUSHBUTTON PANEL

Motor ON/OFF

Upon start-up, the speed is that stored at the previous operation.

Increase speed from 1 to 4

Speed 4 is only active for a few

minutes, then speed 3 activates.

The speeds are indicated by the

LEDs on the keys:

Speed 1

Speed 2

Speed 3

Speed 4

("+" LED ﬂashing)

Reduce speed from 4 to 1

Light on/o

Short impulse: turn light on and oﬀ

Long impulse: change light tone from 2700K to 5600K

TIMER (red LED ﬂashing)

Auto switch-oﬀ after 15 min.

The function deactivates (red LED oﬀ) if:

- The TIMER key ( ) is pressed again.

- The ON/OFF key ( ) is pressed.

USING THE RADIO CONTROL

WARNINGS!:

Place the hood away from sources of electromagnetic waves (e.g.

microwave ovens), which could interfere with the radio control

and with the hood electronics.

The maximum operating distance is 5 metres, that may vary according to

the presence of electromagnetic interferences.

Radio control operated at 433.92MHz.

The radio control consists of two parts:

- the receiver built into the hood;

- the transmitter shown here in the gure.

DESCRIPTION OF TRANSMITTING

COMMANDS

Motor switch-on and speed increase

from 1 to 4. Speed 4 is only active for a

few minutes.

DOWN

Speed decrease and motor switch-oﬀ.

Light ON-OFF

Short impulse:

turn light on and oﬀ

Long impulse:

change light tone from 2700K to 5600K

TIMER ON: The motor automatically

switches oﬀ after 15 min.

The function is automatically disabled if

the motor is switched oﬀ ( key)

Command transmission active

RADIO CONTROL CODE CHANGE

With only one radio control, go directly to point 2.

With several radio controls in the same room, a new code can be created by

following the procedure below.

Disconnect the power to the hood before starting the procedure.

1  CREATE A NEW CODE

The procedure is to be carried out on the radio control.

• Press LIGHT and TIMER simultaneously until the display starts ﬂashing.

• Press DOWN on the radio control: saving is conﬁrmed by three brief ﬂash-

es of the display. The new code cancels and replaces the previous default

code.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falmec Gruppo Incasso NRS Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info