Bedienungsanleitung Falmec Luce - wall (Seite 19 von 88) (Alle Sprachen)

709820

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

24h

Speed 1 button

With LED on (speed 1 already running):

• Pressing this key will switch o the hood motor and the LED associated with the key

With LED oﬀ:

• A short press starts or sets the hood at speed 1 (the function starts when the key is released); when speed 1 is running, the relative

LED lights up.

• With the motor oﬀ, a long press (at least 3 seconds) will start the recirculation function: in this mode (for 24 hours), the hood runs an

operating cycle which involves starting the motor at the 1st speed for 1 hour, followed by 3 hours with the motor down. This cycle is

repeated for 24 hours, until timeout. For these 24 hours, the LED ﬂashes, meaning that the recirculation function is running. With this

feature enabled, you CANNOT select other speeds.

• To deactivate this function, keep the relative key pressed for at least 3 seconds.

Speed 2 button

With LED on (speed 2 already running):

• Nothing will happen when this key is pressed. To switch the hood o ﬁrstly select speed 1, then press the "speed 1 button" again.

With the LED oﬀ and a speed on:

• Press the key (long or not) to set the hood on speed 2. When speed 2 is running the relative LED will light up.

With the LED oﬀ and NO speed on:

• Nothing will happen when this key is pressed.

Speed 3 button

With LED on (speed 3 already running):

• Nothing will happen when this key is pressed. To switch the hood o ﬁrstly select speed 1, then press the "speed 1 button" again.

With the LED oﬀ and a speed on:

• Press the key (long or not) to set the hood on speed 3. When speed 3 is running the relative LED will light up.

With the LED oﬀ and NO speed on:

• Nothing will happen when this key is pressed.

Speed 4 button

With LED on (speed 4 already running):

• Nothing will happen when this key is pressed. To switch the hood o ﬁrstly select speed 1, then press the "speed 1 button" again.

With the LED oﬀ and a speed on:

• Press the key (long or not) to set the hood on speed 4. When speed 4 is running the relative LED will start ﬂashing; the 4th, or inten-

sive, speed is timed and after approximately 7 minutes the motor will automatically switch to 3rd speed.

With the LED oﬀ and NO speed on:

• Nothing will happen when this key is pressed.

Light Button

Light:

• By brieﬂy pressing the key (the back-lit button), you turn the light on and oﬀ.

LIGHTING

The hood has ﬂuorescent lamp lighting.

If the lamp ever needs to be replaced:

• disconnect the appliance from the electrical mains power supply by unplugging it or turning oﬀ the main switch;

Phase

I page 6

• remove the covering element (N) (Fig.

and

);

• take out the blown ﬂuorescent tube (M) (Fig.

and

);

• put in a new ﬂuorescent lamp by performing, in reverse order, the operations described in Fig.

and

;

The new uorescent lamp must be identical to the old one!

• put the covering element back in (N) performing, in reverse order, the operations described in Fig.

and

;

• connect the appliance back up to the electrical power mains.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falmec Luce - wall Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info