• Insert the extension (H) in the chimney (G) (Fig.
1
) and fasten the assembly to the body of the hood using screws (V3)(Fig.
2
).
• With external exhaust (suction) versions, it is possible to insert extension (H) with the slots facing downwards so that they are not visible when the installation
height allows it.
Phase
F page 5
• Slide the extension (H) until it is positioned at the desired height (Fig.
1
).
• Following what is indicated in Fig.
2
, draw a line on the wall that will be used to position the bracket (L) correctly.
• Place the bracket (L) on the wall by following the line drawn on it. With a spirit level, check the horizontal alignment and mark the 2 drilling points at the ends (Fig.
3
).
• Drill the holes, insert 2 expansion plugs (ø 6mm) and fasten the bracket (L) with the relative screws (V4) (Fig.
4
).
• Tighten the extension (H) to the bracket (L) using screws (V5) (Fig.
5
).
• Electrically power the hood in accordance with regulations in force.
OPERATION
WHEN SHOULD THE HOOD BE SWITCHED ON AND OFF?
Switch on the hood at least one minute before starting to cook: this enhances the airflow to convey fumes and vapours towards the suction surface. After cooking,
leave the hood operating until complete extraction of all vapours and odours. If required, by means of the Timer function, it is possible to set hood auto switch-off
after 15 minutes of operation.
WHICH SPEED IS TO BE SELECTED?
The rst speed is a low consumption energy-saving way of keeping the air clean, the second speed is used in normal conditions, and the third speed is used when
there are strong odours and vapours.
WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?
The hood is assembled with two different types of filters: metal ones (washable) and active carbon ones (non-washable). The former must be cleaned every 30 hours
of use (the fixed red light
indicates that they need to be washed), the latter are to be replaced every 3-4 months, depending on the use of the hood. For further
information, please read the chapter regarding "Maintenance" on page 19.
USE OF ELECTRONIC PUSH BUTTON CONTROL PANEL
Timer/Filters alarm
Pressing the key with the motor active at any speed activates the Timer
function: this function determines the auto switch-o of the hood
after 15 minutes of operation. Activation of the function is signalled
by a RED ashing light.
With the Timer function active, the hood can still be switched off by
the user at any time by pressing the key : the function will be auto-
matically disabled and the RED light will turn off. Should the speed be
changed with the Timer function active, the latter will be automatically
disabled.
On the other hand, ignition of the xed RED light indicates a grease
lter alarm: this alarm notifies that it is time to wash the metal an-
ti-grease filters (the alarm is triggered after approximately 30 hours of
use). After cleaning the filters, disable the alarm and reset the counters
by keeping the key pressed for 3 seconds.
To disassemble and assemble the anti-grease metal filters, re-
fer to the instructions on drawing
G
on page 6.
Mode button (ON/OFF)
Pressing the key switches on (or off) the hood motor: it starts at the
previously selected speed prior to switching it off (desired speed func-
tion). Should you wish to use a different speed, set if by using the +
and - keys.
Button +
By pressing the key, the motor speed increases. Speeds 1, 2 and 3 are
displayed by the number of LEDs switched on, excluding the light and
timer LEDs.
The + key in the version with 4 speeds has an intermittent light: the
4th speed or intensity is timed and after approximately 7 minutes the
motor automatically switches to 3rd speed.
Button -
By pressing the key, the motor speed reduces. Speeds 1, 2 and 3 are
displayed by the number of LEDs switched on, excluding the light and
timer LEDs.
Light button
ON: light on (lit button) OFF: light off
LIGHTING
The hood has fluorescent lamp lighting.
If the lamp ever needs to be replaced:
• disconnect the appliance from the electrical mains power supply by unplugging it or turning off the main switch;
Phase I page 6
• remove the covering element (N) (Fig.
1
and
2
);
• take out the blown fluorescent tube (M) (Fig.
3
and
4
);
• put in a new fluorescent lamp by performing, in reverse order, the operations described in Fig.
3
and
4
;
The new uorescent lamp must be identical to the old one!
• put the covering element back in (N) performing, in reverse order, the operations described in Fig.
1
and
2
;
• connect the appliance back up to the electrical power mains.
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Falmec Lumen - wall wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
