Bedienungsanleitung Falmec Melissa Tulip (Seite 10 von 48) (Alle Sprachen)

709795

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

ELECTRICAL CONNECTION

(only intended for qualied personnel)

Disconnect the equipment from electrical mains power supply before carry-

ing out any operations on the hood.

Ensure that the wires inside the hood are not disconnected or cut:

in the event of damage, contact your nearest Servicing Department.

Refer to qualied personnel for electrical connections.

Connection must be carried out in compliance with the provisions of law in force.

Before connecting the hood to the electrical mains power supply, check that:

• voltage supply corresponds with what is reported on the data plate located inside the

hood;

• the electrical system is compliant and can withstand the load (see the technical speci-

cations located inside the hood);

• the power supply plug and cable do not come into contact with temperatures exceed-

ing 70 °C;

• the power supply system is eectively and properly connected to earth in compliance

with regulations in force;

•

the socket used to connect the hood is within reach.

In case of:

• devices tted with cables without a plug: the type of plug to use is a ''standardised'' one.

The wires must be connected as follows: yellow-green for earthing, blue for neutral and

brown for the phase. The plug must be connected to an adequate safety socket.

•

xed equipment not provided with a power supply cable and plug, or any other device

that ensures disconnection from the electrical mains, with an opening gap of the con-

tacts that enables total disconnection in overvoltage category III conditions.

Said disconnection devices must be provided in the mains power supply in compliance

with installation regulations.

The yellow/green earth cable must not be cut o by the switch.

The Manufacturer declines all responsibility for failure to comply with the safety regulations.

FUMES DISCHARGE

EXTERNAL EXHAUST HOOD SUCTION

In this version the fumes and vapours are discharged outside through

the exhaust pipe.

To this end, the hood outlet tting must be connected via a pipe, to an

external output.

The outlet pipe must have:

• a diameter not less than that of the hood tting.

• a slight slope downwards (drop) in the horizontal sections to prevent condensation from

owing back into the motor.

• the minimum required number of bends.

• the minimum required length to avoid vibrations and reduce the suction performance of

the hood.

You are required to insulate the pipes if it passes through cold environments.

In the presence of motors with 800m

/h or higher, a check valve is present to prevent

external air owing back.

Deviation for Germany:

when the kitchen hood is used at the same time as appliances that are powered by energy other

than electricity, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar).

HOOD WITH INTERNAL RECIRCULATION FILTERING

In this model, the air passes through the charcoal lters to be puried

and recycled in the environment.

Ensure that the active carbon lters are assembled into the hood, if not,

install them as indicated in the assembly instructions.

In this version the check valve must not be assembled: remove it if it is on the air

outlet tting of the motor.

ASSEMBLY INSTRUCTIONS

only intended for personnel qualied

The hood can be installed in various congurations.

The generic assembly steps apply to all installations; for each case, follow

the specic steps provided for the required installation.

OPERATION

WHEN TO TURN ON THE HOOD?

Switch on the hood at least one minute before starting to cook to direct fumes and vapours

towards the suction surface.

After cooking, leave the hood operating until complete extraction of all vapours and odours.

By means of the Timer function, it is possible to set auto switch-o function which will allow

the hood to turn o automatically after 15 minutes of operation.

WHICH SPEED IS TO BE SELECTED?

1st speed: maintains the circulation of clean air with low electricity consumption.

2nd speed: normal conditions of use.

3rd speed: presence of strong odours and vapours.

WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?

The metal lters must be cleaned every 30 hours of operation.

The active carbon lters must be replaced every 3-4 months, depending on the use of the

hood.

For further details see the “MAINTENANCE” chap.

USE OF SLIDER

01 0123

LIGHT SWITCH

By placing the slider in position 0, the hood light is o

By placing the slider in position 1, the hood light is on

MOTOR SWITCH

By placing the slider in position 0, the hood motor is o

By placing the slider in position 1, the hood motor is set at minimum speed

By placing the slider in position 2, the motor is set at medium speed

By placing the slider in position 3, the motor is set at high speed

The motor activation is signalled by the switching on of the red light on the slider

USE OF MECHANICAL PUSH BUTTON CONTROL PANEL

OFF 1 2 3

Light on/o

OFF

OFF button

Press this button to switch the motor o

Button 1: Press this button (button in) to start or set

the motor at minimum speed

Button 2: Press this button (button in) to start

or set the motor at medium speed

Button 3: Press this button (button in) to start or

set the motor at maximum speed

Falmec Melissa Tulip Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info