Bedienungsanleitung Falmec Move (Seite 17 von 76) (Alle Sprachen)

709847

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

ENGLISH

INSTALLATION

only intended for qualied personnel

Before installing the hood, carefully read the chapter 'SA-

FETY INSTRUCTIONS AND WARNINGS'.

TECHNICAL FEATURES

The technical specications are exhibited on the labels located inside

the hood.

POSITIONING

The minimum distance between the highest part of the cooking

equipment and the lowest part of the hood is indicated in the in-

stallation instructions.

Generally, when the hood is placed over gas cookers, the distance must

be at least 65 cm (25.6''). However, according to an interpretation of

standard EN60335-2-31 dated 11-07-2002 of TC61 (sub-clause 7.12.1

meeting 15 agenda item 10.11), the minimum distance between the

cooker and lower part of the hood can be reduced to the quota re-

ported in the installation instructions.

Should the instructions for the gas cooker specify a greater distance,

this must be taken into consideration.

Do not install the hood outdoors and do not expose it to outdoor envi-

ronment (rain, wind, etc.).

ELECTRICAL CONNECTION

(only intended for qualied personnel)

Disconnect the equipment from electrical mains power

supply before carrying out any operations on the hood.

Ensure that the wires inside the hood are not disconnected

or cut:

in the event of damage, contact your nearest Servicing Depart-

ment.

Refer to qualied personnel for electrical connections.

Connection must be carried out in compliance with the provisions

of law in force.

Before connecting the hood to the electrical mains power supply,

check that:

• voltage supply corresponds with what is reported on the data plate

located inside the hood;

• the electrical system is compliant and can withstand the load (see

the technical specications located inside the hood);

• the power supply plug and cable do not come into contact with

temperatures exceeding 70 °C;

• the power supply system is eectively and properly connected to

earth in compliance with regulations in force;

•

the socket used to connect the hood is within reach.

In case of:

• devices tted with cables without a plug: the type of plug to use is a

''standardised'' one. The wires must be connected as follows: yellow-

green for earthing, blue for neutral and brown for the phase. The

plug must be connected to an adequate safety socket.

•

xed equipment not provided with a power supply cable and plug,

or any other device that ensures disconnection from the electrical

mains, with an opening gap of the contacts that enables total discon-

nection in overvoltage category III conditions.

Said disconnection devices must be provided in the mains power

supply in compliance with installation regulations.

The yellow/green earth cable must not be cut o by the switch.

The Manufacturer declines all responsibility for failure to comply with

the safety regulations.

FUMES DISCHARGE

HOOD WITH INTERNAL RECIRCULATION FILTERING

In this version, air passes through zeolite-carbon

lters and the E.ION ionising system to be puri-

ed and recycled in the environment. Make sure

the zeolite-carbon lters are installed in the hood,

otherwise, apply them as indicated in the assembly

instructions.

ASSEMBLY INSTRUCTIONS

only intended for personnel qualied

The hood can be installed in various congurations.

The generic assembly steps apply to all installations; for

each case, follow the specic steps provided for the re-

quired installation.

OPERATION

WHEN TO TURN ON THE HOOD?

Switch on the hood at least one minute before starting to cook to direct

fumes and vapours towards the suction surface.

After cooking, leave the hood operating until complete extraction of all

vapours and odours. By means of the Timer function, it is possible to set

auto switch-o function which will allow the hood to turn o automati-

cally after 15 minutes of operation.

AIR QUALITY

Air quality is displayed by the colour of the leaf.

Green = excellent quality.

Yellow = pollutant agents found.

The higher the number of pollutant agents, the

darker the yellow

colour.

WHICH SPEED IS TO BE SELECTED?

1st speed: maintains the circulation of clean air with low electricity

consumption.

2nd speed: normal conditions of use.

3rd speed: presence of strong odours and vapours.

4th speed: rapid disposal of odours and vapours.

(*)Note: 4th speed not included on SPRING and LYBRA models.

WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?

The metal lters must be cleaned every 30 hours of operation.

The zeolite-carbon lters must be reactivated every 18 months and re-

placed every 3 years.

For further details see the “MAINTENANCE” chap.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falmec Move Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info