Bedienungsanleitung Falmec Move (Seite 18 von 76) (Alle Sprachen)

709847

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

TOUCH PUSHBUTTON PANEL

Motor ON/OFF

Upon start-up, the speed is that stored at the previous opera-

tion.

Increase speed from 1 to 4

Speed 4 is only active for a

few minutes, then speed 3

activates.

NOTE: only 3 speeds for

SPRING and LYBRA

The speeds are indicated by

the LEDs on the keys:

Speed 1

Speed 2

Speed 3

Speed 4

("+" LED ashing)

Riduzione velocità da 4 a 1

Automatic cycle: the hood only activates when pollutant

agents are found.

The function deactivates if:

- no pollutant agents are found for 3 hours;

- The TIMER key (

) is pressed again.;

- keys + and - are pressed

Light on/o

TIMER (red LED ashing)

Auto switch-o after 15 min.

The function deactivates (red LED o) if:

- The TIMER key ( ) is pressed again.

- The ON/OFF key ( ) is pressed.

FILTER ALARM (Red LED on with (

) o)

Anti-grease lter maintenance after approximately 30 hours

of operation.

Press (

) for 3 seconds to reset.

MAINTENANCE

Before cleaning or carrying out maintenance operations,

disconnect the equipment by removing the plug or

switching o the main switch.

Do not use detergents containing abrasive, acidic or corrosive

substances or abrasive cloths.

Regular maintenance guarantees proper operation and performance

over time.

Special attention is to be paid to the metal anti-grease lters : fre-

quent cleaning of the lters and their supports ensures that no am-

mable grease is accumulated.

CLEANING OF EXTERNAL SURFACES

You are advised to clean the external surfaces of the hood at least once

every 15 days to prevent oily substances and grease from sticking to

them.

Alternatively and for all the other types of surfaces, it can be cleaned

using a damp cloth, slightly moistened with mild, liquid detergent or

denatured alcohol.

Finish o cleaning by rinsing well and drying with soft cloths.

METAL ANTI-GREASE FILTERS

It is advised to frequently wash the metal lters (at least once a

month) leaving them to soak in boiling water and washing up liquid

for 1 hour, taking care not to bend them.

Do not use corrosive, acid or alkaline detergents.

Rinse them well and wait for them to be completely dry before reas-

sembling them.

They are dishwasher safe.

To extract and insert the metal anti-grease lters see the picture.

Pull !

magnet

Push...pull !

SPRING

ZEOLITE-CARBON FILTERS

Before performing maintenance on zeolite-carbon lters

(FCZ), remove the lower dust lter (F) and vacuum any de-

posited dust with a vacuum cleaner.

In normal use conditions, we recommend regenerating the zeolite-car-

bon lter every 18 months and replacing it after 3 years. Simply place it

Do not use too much water next to the push button con-

trol panel and lighting devices in order to prevent humid-

ity from reaching electronic parts.

The glass panels can only be cleaned with specic, non-corrosive or

non-abrasive detergents using a soft cloth.

The Manufacturer declines all responsibility for failure to comply with

these instructions.

CLEANING OF INTERNAL SURFACES

It is forbidden to clean electrical parts, or parts related to

the motor inside the hood, with liquids or solvents.

For the internal metal parts, see the previous paragraph.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falmec Move Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info