Bedienungsanleitung Falmec Vetra 90 (Seite 25 von 72) (Alle Sprachen)

709763

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH

ELECTRICAL CONNECTION

(only intended for qualied personnel)

Disconnect the equipment from electrical mains power supply before carry-

ing out any operations on the hood.

Ensure that the wires inside the hood are not disconnected or cut:

in the event of damage, contact your nearest Servicing Department.

Refer to qualied personnel for electrical connections.

Connection must be carried out in compliance with the provisions of law in force.

Before connecting the hood to the electrical mains power supply, check that:

• voltage supply corresponds with what is reported on the data plate located inside the

hood;

• the electrical system is compliant and can withstand the load (see the technical speciﬁ-

cations located inside the hood);

• the power supply plug and cable do not come into contact with temperatures exceed-

ing 70 °C;

• the power supply system is eﬀectively and properly connected to earth in compliance

with regulations in force;

•

the socket used to connect the hood is within reach.

In case of:

• devices ﬁtted with cables without a plug: the type of plug to use is a ''standardised'' one.

The wires must be connected as follows: yellow-green for earthing, blue for neutral and

brown for the phase. The plug must be connected to an adequate safety socket.

•

ﬁxed equipment not provided with a power supply cable and plug, or any other device

that ensures disconnection from the electrical mains, with an opening gap of the con-

tacts that enables total disconnection in overvoltage category III conditions.

Said disconnection devices must be provided in the mains power supply in compliance

with installation regulations.

The yellow/green earth cable must not be cut oﬀ by the switch.

The Manufacturer declines all responsibility for failure to comply with the safety regulations.

FUMES DISCHARGE

HOOD WITH INTERNAL RECIRCULATION FILTERING

In this version, air passes through zeolite-carbon ﬁlters to be

puriﬁed and recycled in the environment. Make sure the zeolite-

carbon ﬁlters are installed in the hood, otherwise, apply them as

indicated in the assembly instructions.

ASSEMBLY INSTRUCTIONS

only intended for personnel qualied

The hood can be installed in various congurations.

The generic assembly steps apply to all installations; for each case, follow

the specic steps provided for the required installation.

OPERATION

WHEN TO TURN ON THE HOOD?

Switch on the hood at least one minute before starting to cook to direct fumes and vapours

towards the suction surface.

After cooking, leave the hood operating until complete extraction of all vapours and odours.

By means of the Timer function, it is possible to set auto switch-oﬀ function which will allow

the hood to turn oﬀ automatically after 15 minutes of operation.

WHICH SPEED IS TO BE SELECTED?

1st speed: maintains the circulation of clean air with low electricity consumption.

2nd speed: normal conditions of use.

3rd speed: presence of strong odours and vapours.

4th speed: rapid disposal of odours and vapours.

WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?

The metal ﬁlters must be cleaned every 30 hours of operation.

The zeolite-carbon ﬁlters must be reactivated every 18 months and replaced every 3 years.

For further details see the “MAINTENANCE” chap.

ROTARY SWITCH - CONTROLS

(DAMA - LOOP - SOFFIO - SOPHIE)

OFF

PUSH

OFF

Motor OFF

speed 1 (green light)

I I

speed 2 (blu light)

I I I

speed 3 (violet light)

PUSH

speed 4 (red light). It is activated by pressing the button for 2 se-

conds. After a few minutes it comes back ti speed 3.

Pressing for a second:

On / o light

TIMER (can only be activated by remote control)

(ﬂashing)

Auto switch-oﬀ after 15 min.

The function deactivates (red LED oﬀ) if:

The TIMER key

is pressed again or motor OFF.

FILTER ALARM (motor OFF)

Anti-grease ﬁlter maintenance after approximately 30 hours of operation.

Press

for 4 seconds to reset.

ELECTRONIC PUSHBUTTON PANEL

(MATERIA - VETRA)

Motor ON/OFF

Upon start-up, the speed is that stored at the previous operation.

Increase speed from 1 to 4

Speed 4 is only active for a few min-

utes, then speed 3 activates.

The speeds are indicated by the LEDs

on the keys:

Speed 1

Speed 2

Speed 3

Speed 4

("+" LED ﬂashing)

Reduce speed from 4 to 1

Light on/o

TIMER (red LED ﬂashing)

Auto switch-oﬀ after 15 min.

The function deactivates (red LED oﬀ) if:

- The TIMER key (

) is pressed again.

- The ON/OFF key (

) is pressed.

FILTER ALARM (red LED steady on with ( ) oﬀ)

Anti-grease ﬁlter maintenance after approximately 30 hours of operation.

Press (

) the meter for 3 seconds to reset.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falmec Vetra 90 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info