Bedienungsanleitung Fantasy Aspire 2019 (Seite 13 von 24) (Englisch)

784937

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

CONTROL PANEL OPERATION

INITIAL START-U

P - When the spa is

first powered up the control system begins a 2

minute Startup Mode. Different codes will display

on the screen. Once Startup

Mode completes,

the actual temperature is displayed on the

screen, and the spa will then begin to heat and

maintain the water temperature and the first filter

cycle will start. Your spa has been designed so

that it will automatically heat the water to the

factory set temperature of 38°C unless you set

the spa to a different temperature. If power is

disconnected from the spa, it will automatically

revert back to the last saved set temperature

when power is reapplied.

TEMPERATURE

ADJUSTMENT (26.5°C-40°C)

The temperature can only function between

26.5°C - 40°C. The last measured temperature will

constantly display on LCD.

Press the Plus or Minus buttons to display the set

temperature and indicator . Each time either

button is pressed again, the set temperature will

increase or decrease depending on which button

is pressed. After five seconds, the LCD will

automatically display the current spa temperature.

The “heater” indicator lights up when the

heater is on. It flashes when there is a request

for more heat, but the heater is not on. Once set

temperature is reached the indicator shuts off

and the low speed of the jet pump turns off after

30 seconds (if not in filter cycle).

JETS OPERATION

Firmly press the Jets button once to activate the

low speed of the pump and again for the high

speed. Firmly press the Jets button again to turn

off the pump. If left running the low or high speed

pump will automatically turn off after 1 hour. The

"Jets" indicator light next to the button will blink

when jet pump is on low speed and is solid on

high speed.

MULTI COLOR LED LIGHT

Press the Light button once to turn on the light,

the light indicator next to the button is lit when the

light is on. Press the button again to turn the light

off. Every time the light is quickly turned off and

on a new light mode will appear. The sequence is

as follows: White, Aqua, Magenta, Azure, Amber,

Emerald, Ruby, color wheel with abrupt color

changes, slow full color wheel and fast full color

wheel. The last light mode used will come back

on when the light is turned off for more than 2

seconds.

NOTE: If left on, the light will automatically turn off

after 4 hours of operation.

FILTER CYCLES

There are two filter cycles: the first cycle (F1)

starts right after power up and the second cycle

(F2) will start 12 hours later. The default duration

for the first filter cycle is 1 hour, and 30 minutes

for the second cycle. Filter cycles only run at low

speed. The “Filter” indicator lights up when a

filter cycle is on. The duration of each filter cycle

can be modified.

ADJUSTING PRESET FILTER

CYCLES

Filter duration is programmable between 0 and 6

hours in 30 minute increments (0.5 hours) for both

filter cycles. To program the cycle times:

1. Press and hold Mode button for 5 seconds

until F1 is displayed.

2. Press the Plus or Minus button to adjust

the cycle time for F1.

Jets

Indicator Lights

Temp Minus

Temp Plus

Light Mode

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fantasy Aspire 2019 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info