Bedienungsanleitung Fantasy Drift 2019 (Seite 18 von 24) (Englisch)

784933

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ADDING START-UP CHEMICALS

WATER CHEMISTRY

GUIDELINES

The following step-by-step instructions are a

recommended guideline for balancing water

chemistry. If unsure about any step in the

process, please contact your local Dealer.

Initially, it is advisable to identify what minerals

(e.g. iron) are present in the local source water.

This will provide a better understanding of how

to treat the water. Please follow the four steps

below and be sure to achieve the correct levels

in each area before moving onto the next step.

ADD all chemicals into filter compartment while

running jets for 10 minutes.

STEP #1: ESTABLISH PROPER PH

LEVEL:

The recommended range for pH is between

7.2 and 7.8. If the reading is too high, lower

the pH by using a pH Down/Decreaser

(sodium bisulfate). If the pH level needs to

be increased, do so with a pH Up/Increaser

(sodium hydrogen carbonate). Any pH Up

or Down should be added one teaspoon

at a time, waiting one-half hour between

application and re-measuring.

STEP #2: MEASURE TOTAL

ALKALINITY:

The ideal range is between 40-120 parts

per million (PPM). If the total alkalinity is

too high, it should be reduced by using

an Alkalinity Down/Decreaser (sodium

bisulfate). If the total alkalinity is too low, it

can be increased by adding an Alkalinity UP/

Increaser (sodium bicarbonate or sodium

hydrogen carbonate). These products should

be added in small amounts – 5 ml at a time.

After adding 5 ml, wait one half hour before

re-measuring. Once the safe range of total

alkalinity is established, proceed to the next

step.

STEP #3: DETERMINE CALCIUM

HARDNESS:

It is important to bring the calcium reading to

between 50-150 PPM. If the reading requires

adjustment, it should now be corrected. If

the water is too soft (a low reading) calcium

hardness should be added to the water to

increase the PPM reading. If the water is too

hard (a high reading), it can be corrected by

either: (A) a mixture of hard and soft water

added to attain a reading in the safe range,

or (B) addition of stain and scale control. If

calcium hardness is a problem with the local

source water (either too hard or too soft) a

test kit, which measures calcium hardness, is

essential.

STEP #4: SANITIZING:

After steps 1-3 are complete, the spa must

be sanitized using Chlorine (sodium

dichlor). Add 2 teaspoons of Chlorine, and

increase as necessary to reach a level of

3-5 ppm. Check and maintain this level

weekly, and before and after using the spa.

IMPORTANT NOTE: A granulated sodium

dichlor is highly recommended for sanitizing

spa water, granular bromine may also be

used. Never use compressed sanitizers

even with a floater. As with any other

chemicals, the sanitizer should be introduced

to the spa with the jets running a minimum of

10 minutes.

WEEKLY SHOCK:

Using a potassium monopersulfate (MPS)

shock, add approximately 60 ml over the

filter while the jets are running. Shocking is

achieved by adding the MPS to turbulent

water. Leave the cover up and jets on high

for 10 minutes. Then shut jets off and return

the cover to the closed position to maintain

heat.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fantasy Drift 2019 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info