784936
11
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
8
ELECTRICAL REQUIREMENTS
ELECTRICAL
REQUIREMENT
DO NOT POWER THE SPA WITHOUT
FIRST FILLING WITH WATER!
DANGER – RISK OF ELECTRIC
SHOCK
Installations that do not conform to the
following procedures and requirements
may expose users to electric shock. Non-
conforming installations will not be covered
under warranty.
The electrical wiring of this spa must meet the
requirements of your National Electric Code and
any applicable local codes. The electrical circuit
must be installed by an electrical contractor and
approved by a local building electrical inspection
authority.
1. Installations within 1.5 m of any metal surfaces
must ground the metal surfaces to the spa.
Use an 8 mm² solid copper wire and attach it
to the grounding lug on the control box, located
in the equipment compartment.
2. Only a licensed electrician may install power to
the spa.
3. Power supply installation must include a
suitably rated ground fault circuit interrupter
(GFCI) as required by your national/local
electric code. The circuit breaker must be
dedicated and should not be shared with any
other appliances. It must be labeled and easily
accessible to users.
4. The electrical supply for the spa must include a
suitable circuit breaker to open all ungrounded
supply conductors to comply with your
national/local electric code. The disconnecting
means must be readily accessible to the spa’s
occupant but installed at least
1.5 m from the spa water.
5. Power supply lines must be hard wired
into the power pack. When hard wired,
the use of a shut-off box near the spa is
also recommended. This box provides a
quick and convenient method to shut off
power to the spa for emergencies and
maintenance.
6. Supply lines must be properly sized as per
your national/local electric code. A ground line
must be provided that is as large as the largest
current carrying conductor, but no less than 8
mm². Use copper wiring only.
7. Please open the front cover of the control box,
and follow the instructions and wiring diagram
printed on the backside.
8. 230V HARD WIRED SPAS
Wire size must be appropriate per your
national electric code and/or local codes.
Wire size is determined by length of run
from breaker box to spa and maximum
current draw.
All wiring must be copper to ensure
adequate connections. Do not use
aluminum wire.
Equipment access is below
the topside control panel on
most spas.
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Fantasy Embrace 2019 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info