Bedienungsanleitung Fein ABLS 1.6 E (Seite 18 von 141) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

577148

Zoom out

Zoom in

Vorherige Seite

1/141

Nächste Seite

Do not direct the power tool against yourself, other per-

sons or animals. Danger of injury from sharp or hot

application tools.

Use and handling of the battery (battery pack).

To avoid hazardous situations such as burns, fire, explo-

sion, skin injuries, and other injuries when handling the

battery, observe the following instructions:

Batteries must not be disassembled, opened or reduced

in size. Do not subject batteries to mechanical impact or

shock. Hazardous vapours and fluid can escape in case of

damage and improper use of the battery. The vapours can

irritate the respiratory system. Liquid ejected from the

battery may cause skin irritations or burns.

When battery fluid from a damaged battery has come into

contact with objects close by, check the respective com-

ponents, clean them or replace them as required.

Keep the battery away from heat and fire. Do not store the

battery in direct sunlight.

Do not remove the battery from its original packaging

until it is going to be used.

Before any work on the machine itself, remove the bat-

tery from the power tool. If the power tool accidentally

starts, there is danger of injury.

Remove the battery only when the power tool is switched

off.

Keep the battery away from children.

Keep the battery clean and protect it against moisture

and water. Clean contaminated battery terminals and

power tool connections with a dry, clean cloth.

Use only intact original FEIN batteries that are intended

for your power tool. When working with and charging

incorrect, damaged, repaired or reconditioned batteries,

imitations or other brands, there is danger of fire and/or

explosion.

Follow the safety warnings in the operating instructions

of the battery charger.

Hand/arm vibrations

The vibration emission level given in this information

sheet has been measured in accordance with a standard-

ised test given in EN 60745 and may be used to compare

one tool with another. It may be used for a preliminary

assessment of exposure.

The declared vibration emission level represents the

main applications of the tool. However, if the tool is used

for different applications, with different accessories or

poorly maintained, the vibration emission may differ.

This may significantly increase the exposure level over

the total working period.

An estimation of the level of exposure to vibration

should also take into account the times when the tool is

switched off or when it is running but not actually doing

the job. This may significantly reduce the exposure level

over the total working period.

Identify additional safety measures to protect the opera-

tor from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation

of work patterns.

Operating Instructions.

Guide the power tool toward the work piece only

when switched on.

While cutting, hold the power tool as upright as possible

to the work-piece surface (ABLS).

Guide the power tool uniformly and with light feed in the

cutting direction. Excessive feed reduces the tool life of

the application tools.

Do not cut steel sheets where welded. Do not cut lay-

ered sheets exceeding the max. work-piece thickness.

To increase the tool life of the blades, it is recommended

to apply a lubricating agent alongside the intended cutting

line:

– For cuts in steel sheet: Cutting paste or cutting oil.

– For cuts in aluminium: Petroleum.

Do not switch the power tool off until after having

removed it from the cutting path.

The symptom for worn blades is a clearly increased feed

force at lower working progress.

ABSS: For inside cuts, a pilot hole is required; see “Tech-

nical Data”.

Blades and cutting bars cannot be reground.

ABLS: The blades cannot be reground and must always be

replaced in pairs.

Handling the battery.

Operate and charge the battery only within the battery

operating-temperature range of 0°C – 45°C (32°F –

113°F). At the beginning of the charging procedure, the

battery temperature must be within the battery operat-

ing-temperature range.

The real percentage of the battery charge condition is

only indicated when the power tool motor is stopped.

The electronics automatically switch off the motor prior

to the battery being deep discharged.

Repair and customer service.

When working metal under extreme operat-

ing conditions, it is possible for conductive

dust to settle in the interior of the power tool.

Blow out the interior of the power tool via the ventila-

tion slots frequently with dry and oil-free compressed air.

The current spare parts list for this power tool can be

found in the Internet at www.fein.com.

If required, you can change the following parts yourself:

Application tools, cutting bars (ABSS)

LED indicator Meaning Activity

1 – 4 green

LED

Percentage of

charge condi-

tion

Operation

Continuous

red light

Battery is

almost empty

Charge battery

Red flashing

light

Battery is not

ready for

operation

Bring the battery into

the battery operating-

temperature range,

then charge

OBJ_BUCH-0000000121-001.book Page 18 Friday, May 24, 2013 9:52 AM

Fein ABLS 1.6 E Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info