Bedienungsanleitung Fein ASW14-6 PC (Seite 16 von 133) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

576097

Zoom out

Zoom in

Vorherige Seite

1/133

Nächste Seite

For your safety.

Read all safety warnings and all

instructions. Failure to follow the

warnings and instructions may result in electric shock,

fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-

oughly read and completely understood this

Instruction Manual and the enclosed “General

Safety Instructions” (document number

3 41 30 054 06 1). The documents mentioned should be

kept for later use and enclosed with the power tool,

should it be passed on or sold.

Please also observe the relevant national industrial safety

regulations.

Intended use of the power tool:

Hand-held screwdriver for screwing in and unscrewing

screws and nuts in weather-protected environments

without water supply using the application tools and

accessories recommended by FEIN.

Special safety instructions.

Hold power tool by insulated gripping surfaces, when

performing an operation where the fastener may contact

hidden wiring. Fasteners contacting a “live” wire may

make exposed metal parts of the power tool “live” and

could give the operator an electric shock.

Beware of any concealed electric cables, gas or water

conduits. Check the working area before commencing

work, e.g. with a metal detector.

Secure the work piece firmly. A work piece that is

gripped tightly in a clamping device or vice, is more

secure than if held by hand.

Hold the power tool firmly. High reaction torque can

briefly occur.

Do not machine any material containing asbestos. Asbes-

tos is cancerogenic.

Do not rivet or screw any name-plates or signs onto the

power tool. If the insulation is damaged, protection

against an electric shock will be ineffective. Adhesive

labels are recommended.

Do not use accessories which are not specifically

designed and recommended by the power tool manufac-

turer. Safe operation is not ensured merely because an

accessory fits your power tool.

Never look or stare into the light of the power tool’s lamp

from a short distance. Never point the light of the lamp

into the eyes of other persons in close vicinity. The radi-

ation produced by the lamp can be harmful for the eye.

Use and handling of the battery (battery pack).

To avoid hazardous situations such as burns, fire, explo-

sion, skin injuries, and other injuries when handling the

battery, observe the following instructions:

Batteries must not be disassembled, opened or reduced

in size. Do not subject batteries to mechanical impact or

shock. Hazardous vapours and fluid can escape in case of

damage and improper use of the battery. The vapours can

irritate the respiratory system. Liquid ejected from the

battery may cause skin irritations or burns.

When battery fluid from a damaged battery has come into

contact with objects close by, check the respective com-

ponents, clean them or replace them as required.

Keep the battery away from heat and fire. Do not store the

battery in direct sunlight.

Do not remove the battery from its original packaging

until it is going to be used.

Before any work on the machine itself, remove the bat-

tery from the power tool. If the power tool accidentally

starts, there is danger of injury.

Remove the battery only when the power tool is switched

off.

Keep the battery away from children.

Keep the battery clean and protect it against moisture

and water. Clean contaminated battery terminals and

power tool connections with a dry, clean cloth.

Use only intact original FEIN batteries that are intended

for your power tool. When working with and charging

incorrect, damaged, repaired or reconditioned batteries,

imitations or other brands, there is danger of fire and/or

explosion.

Follow the safety warnings in the operating instructions

of the battery charger.

Hand/arm vibrations

The vibration emission level given in this information

sheet has been measured in accordance with a standard-

ised test given in EN 60745 and may be used to compare

one tool with another. It may be used for a preliminary

assessment of exposure.

The declared vibration emission level represents the

main applications of the tool. However, if the tool is used

for different applications, with different accessories or

poorly maintained, the vibration emission may differ.

This may significantly increase the exposure level over

the total working period.

An estimation of the level of exposure to vibration

should also take into account the times when the tool is

switched off or when it is running but not actually doing

the job. This may significantly reduce the exposure level

over the total working period.

Identify additional safety measures to protect the opera-

tor from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation

of work patterns.

m/s

Vibrational emission value (screwdriving)

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

min, m/s

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

min, m/s

Basic and derived units of measurement from the

international system of units SI.

Character Unit of measurement,

international

Unit of measurement,

national

Explanation

WARNING

OBJ_BUCH-0000000119-001.book Page 16 Thursday, June 6, 2013 10:44 AM

Fein ASW14-6 PC Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info