Bedienungsanleitung Fein FMM350Q (Seite 17 von 129) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

577145

Zoom out

Zoom in

Vorherige Seite

1/129

Nächste Seite

Hand/arm vibrations

The vibration emission level given in this information

sheet has been measured in accordance with a standard-

ised test given in EN 60745 and may be used to compare

one tool with another. It may be used for a preliminary

assessment of exposure.

The declared vibration emission level represents the

main applications of the tool. However, if the tool is used

for different applications, with different accessories or

poorly maintained, the vibration emission may differ.

This may significantly increase the exposure level over

the total working period.

An estimation of the level of exposure to vibration

should also take into account the times when the tool is

switched off or when it is running but not actually doing

the job. This may significantly reduce the exposure level

over the total working period.

Identify additional safety measures to protect the opera-

tor from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation

of work patterns.

Emission values for vibration

Operating Instructions.

Do not use accessories not specifically intended and

recommended for this power tool by FEIN. The use of non-

original FEIN accessories can lead to overheating of the

power tool and destroy it.

Guide the power tool toward the work piece only

when switched on.

The application tool can be offset in 45° steps and fas-

tened in the most favourable working position.

Changing the tool (see page 5).

Firmly press in the fastening element to the stop.

Then lock the clamping lever.

Protect your hand and fingers against bruising when

locking the clamping lever. The clamping lever

snaps back vigorously by means of spring force.

Notes on sanding.

Press the power tool with the sanding sheet briefly and

firmly against a flat surface and briefly switch the power

tool on. This provides for good adhesion and prevents

premature wear.

When only one tip or corner of the sanding sheet is

worn, it can be removed again and reattached turned by

120°.

Work with the entire surface of the sanding plate, not

only with the tip.

When sanding with the triangle sanding plate, select a

high oscillating frequency (electronics level 4 –6); when

sanding with the round sanding plate, select a moderate

oscillating frequency (max. electronics level 4).

Sand with continuous motion applying moderate pres-

sure. Applying excessive pressure does not increase the

rate of removal, it only wears off the sanding sheet faster.

Notes on profile sanding.

Select a medium oscillating frequency.

Notes on sawing.

Select a high oscillating frequency. Round saw blades can

be released and clamped offset again, to allow for uni-

form wearing off.

Notes on scraping.

Select a moderate to high oscillating frequency.

Repair and customer service.

When working metal under extreme operat-

ing conditions, it is possible for conductive

dust to settle in the interior of the power tool.

The total insulation of the power tool can be impaired.

Blow out the interior of the power tool via the ventila-

tion slots frequently with dry and oil-free compressed air,

and connect a residual current device (RCD) on the line

side.

If the supply cord of this power tool is damaged, it must

be replaced by a specially prepared cord available through

the FEIN customer service centre.

For storage of the power tool, remove the application

tool, shut the clamping lever, and then press in the fasten-

ing element.

The current spare parts list for this power tool can be

found in the Internet at www.fein.com.

If required, you can change the following parts yourself:

Fastening element, clamping bolt, application tools

Warranty and liability.

The warranty for the product is valid in accordance with

the legal regulations in the country where it is marketed.

In addition, FEIN also provides a guarantee in accordance

with the FEIN manufacturer’s warranty declaration.

The delivery scope of your power tool may include only

a part of the accessories described or shown in this

Instruction Manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product

conforming with the relevant provisions given on the last

page of this Instruction Manual.

Technical documents at: C. & E. Fein GmbH, C-DB_IA,

D-73529 Schwäbisch Gmünd

Environmental protection, disposal.

Packaging, worn out power tools and accessories should

be sorted for environmental-friendly recycling.

Vibration

Classification of FEIN application

tools according to vibration class

Weighted

acceleration*

VC0

< 2.5 m/s

VC1

< 5 m/s

VC2

< 7 m/s

VC3

< 10 m/s

VC4

< 15 m/s

VC5

> 15 m/s

a 3 m/s

* These values are based on a work cycle consisting of no-load

and full-load operation of the same duration.

For information on the vibration class assigned to the application

tool, please see the enclosed data sheet 3 41 30 421 06 0.

OBJ_BUCH-0000000135-003.book Page 17 Friday, September 26, 2014 12:40 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fein FMM350Q Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info