Bedienungsanleitung Fein FSC2.0Q (Seite 19 von 134) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

502702

Zoom out

Zoom in

Vorherige Seite

1/134

Nächste Seite

For your safety.

Read all safety warnings and all

instructions. Failure to follow the

warnings and instructions may result in electric shock,

fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-

oughly read and completely understood this

Instruction Manual and the enclosed “General

Safety Instructions” (document number

3 41 30 054 06 1). The documents mentioned should be

kept for later use and enclosed with the power tool,

should it be passed on or sold.

Please also observe the relevant national industrial safety

regulations.

Intended use of the power tool:

Hand-guided power tool for use without water supply in

weather-protected environments using the application

tools and accessories recommended by FEIN.

FSC1.6X/FSC1.6Q:

– for cutting polyurethane beads for glazier work in

automobiles, lorries and busses

– for sawing out chassis sections and removing under-

seal materials

– for sanding of chassis parts

FSC2.0Q:

– for sawing wood (max. 78 mm), plastic, glass-fibre

reinforced plastics (GFRP) and for sawing sheet metal

(max. 1 mm)

– for removing tile joints and rasping or scraping off tile

grout or carpet remainders

– for cutting elastic sealants (silicone or acrylic) on

facades/frontages and for roughing groove faces

– for sanding or rasping of smaller surfaces.

This power tool is also suitable for use with AC genera-

tors with sufficient power output that correspond to the

Standard ISO 8528, design type G2. This Standard is par-

ticularly not complied with when the so-called distortion

factor exceeds 10 %. When in doubt, please refer to the

generator instruction/specification guide.

Special safety instructions.

Hold power tool by the insulated gripping surfaces, when

performing an operation where the cutting accessory

may contact hidden wiring or its own cord. Cutting acces-

sory contacting a “live” wire may make exposed metal

parts of the power tool “live” and could give the opera-

tor an electric shock.

Use clamps or another practical way to secure and sup-

port the workpiece to a stable platform. Holding the

work by hand or against your body leaves it unstable and

may lead to loss of control.

Grasp the power tool in such a safe manner that your

body never comes into contact with the application tool,

especially while working with application tools such as

saw blades or other blades pointed toward the grasping

range. Touching sharp tips or cutting edges can lead to

injuries.

Wear personal protective equipment. Depending on appli-

cation, use face shield, safety goggles or safety glasses.

Where appropriate, wear dust mask, hearing protectors,

gloves and workshop apron capable of stopping small

abrasive or workpiece fragments. The eye protection

must be capable of stopping flying debris generated by

various operations. The dust mask or respirator must be

capable of filtrating particles generated by your opera-

tion. Prolonged exposure to high intensity noise may

cause hearing loss.

Do not direct the power tool against yourself, other per-

sons or animals. Danger of injury from sharp or hot

application tools.

Do not rivet or screw any name-plates or signs onto the

power tool. If the insulation is damaged, protection

against an electric shock will be ineffective. Adhesive

labels are recommended.

Clean the ventilation openings on the power tool at regu-

lar intervals using non-metal tools. The blower of the

motor draws dust into the housing. An excessive accu-

mulation of metallic dust can cause an electrical hazard.

Before putting into operation, check the mains connec-

tion and the mains plug for damage.

Recommendation: The tool should always be supplied

with power via a residual current device (RCD) with a

rated current of 30 mA or less.

Handling hazardous dusts

For work procedures with this power tool where mate-

rial is removed, dusts develop that can be hazardous to

one’s health.

Contact with or inhaling some dust types, e. g. asbestos

and asbestos-containing materials, lead-containing coat-

ings, metal, some wood types, minerals, silicate particles

from materials containing stone, paint solvents, wood

preservatives, antifouling paints for vessels, can trigger

allergic reactions to the operator or bystanders and/or

lead to respiratory infections, cancer, birth defects or

other reproductive harm. The risk from inhaling dusts

depends on the exposition. Use dust extraction matched

appropriately for the developing dust, as well as personal

protective equipment and provide for good ventilation of

pCpeak

dB dB Peak sound pressure level

K... Uncertainty

m/s

Vibrational emission value according to

EN 60745 (vector sum of three directions)

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

min, m/s

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

min, m/s

Basic and derived units of measurement from the

international system of units SI.

Character Unit of measurement,

international

Unit of measurement,

national

Explanation

WARNING

OBJ_BUCH-0000000084-001.book Page 19 Tuesday, July 17, 2012 9:00 AM

Fein FSC2.0Q Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info