Bedienungsanleitung Fein MBS23 (Seite 17 von 66) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

575162

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

For your safety.

Read all safety warnings and all instruc-

tions provided with the magnetic drill

stand or the power tool.

Failure to fol-

low the warnings and instructions may result in electric

shock, fire and/or serious injury.

Save all safety warnings and instructions for future refer-

ence.

Do not use this product before you have thor-

oughly read and completely understood this

Instruction Manual and the enclosed “General

Safety Instructions” (document number

3 41 30 054 06 1

). The documents mentioned should

be kept for later use and enclosed with the product,

should it be passed on or sold.

Please also observe the relevant national industrial safety

regulations.

Intended use of the magnetic drill stand:

Magnetic drill stand for holding a drive motor, for drilling

with core drill bits and solid drill bits, reaming and tapping

on materials with surfaces suitable for magnets in

weather-protected environments using the application

tools and accessories recommended by FEIN.

Special safety instructions.

Pull the plug from the mains receptacle and/or remove the

battery before making adjustments on the tool or changing

tool accessories.

Unintentional switching on of the power

tool is the cause of many accidents.

Before mounting the power tool, install the magnetic drill

stand correctly.

The correct installation is important in

order to prevent the risk of the drill stand folding

together.

Fasten the power tool securely to the magnetic drill stand

before using it.

Slipping off of the power tool on the mag-

netic drill stand can lead to loss of control.

Do not overload the magnetic drill stand.

Overloading the

magnetic drill stand can cause it to tip over.

Wear personal protective equipment. Depending on appli-

cation, use face shield, safety goggles or safety glasses. As

appropriate, wear dust mask, hearing protectors, gloves

and workshop apron capable of stopping small abrasive or

workpiece fragments.

The eye protection must be capable

of stopping flying debris generated by various operations.

The dust mask or respirator must be capable of filtrating

particles generated by your operation. Prolonged expo-

sure to high intensity noise may cause hearing loss.

When there is danger of falling down, secure the magnetic

drill stand using the provided lashing strap; especially

when working aloft, on vertical building elements or over-

head.

In case of a power failure or when the mains plug

is pulled, the magnetic holding power is not maintained.

Prevent (cooling) liquids from penetrating into the mag-

netic drill stand, especially when working on walls and ceil-

ings.

Penetrating liquids can lead to danger of an electric

shock.

Operate the magnetic drill stand only from socket outlets

with the earthing contact according to regulations. Only use

undamaged supply cords and regularly checked extension

cords with earthing contact.

A protective conductor with-

out continuity can lead to electric shock.

Do not direct the power tool against yourself, other persons

or animals.

Danger of injury from sharp or hot application

tools.

Do not rivet or screw any name-plates or signs to the mag-

netic drill stand.

If the insulation is damaged, protection

against an electric shock will be ineffective. Adhesive

labels are recommended.

Do not use accessories not specifically intended and recom-

mended for the magnetic drill stand by the manufacturer.

Just because the accessory can be attached to your mag-

netic drill stand, it does not assure safe operation.

Before putting into operation, check the mains connection

and the mains plug for damage.

Recommendation: Always operate the power tool via a

residual current device (RCD) with a rated residual current

of 30 mA or less.

Operating instructions.

When a power tool is mounted that is

not intended for use with the magnetic

drill stand, the magnetic drill stand can

tip over.

Use the magnetic drill stand suitable for the performance

characteristics of your drive motor.

Please make sure that the contacting surface for the mag-

netic foot is level, clean and rust-free. Remove any var-

nish or primer.

Use the magnetic drill stand only with the magnetic foot

switched on.

When working on materials that are not magnetizable,

suitable fixation devices, obtainable as accessories from

FEIN, e. g. suction plate, vacuum plate or pipe-drilling

device must be used.

Character Unit of measure,

international

Unit of measure,

national

Explanation

mm mm Adjustment range

l x w mm mm Magnetic foot plate dimensions

mm mm d

= collar diameter of drive motor

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

min, m/s

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

min, m/s

Basic and derived units of measure from the inter-

national system of units SI.

WARNING

3 41 01 128 06 0.book Seite 17 Dienstag, 15. März 2011 8:58 08

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fein MBS23 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info