Bedienungsanleitung Fein MOtlx 6-25 (Seite 12 von 70) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

502703

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

For all work or when changing application tools, always

wear protective gloves. Danger of injury from the sharp

edges of the application tools. Application tools can

become very hot while working. Danger of burns!

Never direct the application tool against yourself. Hold the

pneumatic tool in such a manner that the application tool

cannot come into contact with your hand.

Hand/arm vibrations.

Whilst working with this power tool, hand/arm vibra-

tions will occur.

Adopt the correct working practices in order to reduce

the exposure to vibration:

– in the case of strong vibration, take the recommended

work breaks or change your task more frequently,

– keep your hands warm,

– whilst working, only grip the power tool as firmly as

necessary,

– work only with technically sound machines and appli-

cation tools,

– use the FEIN vibration-absorbing, gel working gloves,

If these recommendations are not observed, the expo-

sure to strong vibration during daily work over a longer

period of time can be detrimental to health.

The maximum exposure values stipulated in the indus-

trial safety directives (e. g. in directive 2002/44/EC, a

maximum daily exposure limit of 5 m/s

relating to a

normal duration of 8 hours) must not be exceeded.

The value of the estimated weighted acceleration

obtained in the laboratory can serve for predicting the

exposure to vibration. During work, weighted accelera-

tions will be dependent on the particular application, and

deviation from this laboratory value can occur.

Emission values for sound and vibration

(Two-figure – specifications as per ISO 4871)

* These values are based on a work cycle consisting of

no-load and full-load operation of the same duration.

Intended use of the pneumatic tool.

hand-guided pneumatic tool for commercial use, for cut-

ting plastic beads and similar materials, particularly for

cutting out windscreens, rear and side window panes for

the automobile workshop using the application tools and

accessories recommended by FEIN.

Connection to air supply.

For trouble-free operation of the air tool, use a filter/reg-

ulator-lubricator consisting of water separator, oil lubri-

cator and compressed-air regulator.

Check that the pressure in the compressed-air supply

conforms with the pressure given on the rating plate on

the pneumatic tool.

➤ Before connecting, blow through the hose.

The hose should have a minimum diameter of 16 mm.

The opening of the valve and the coupling should have a

diameter of at least 8 mm.

Operating instructions.

When uncoupling hose couplings, first shut the ball valve,

then actuate the pneumatic tool, and then uncouple. Do

not uncouple the hose coupling until after the com-

pressed air has been completely relieved.

Repair and customer service.

Maintain and clean the pneumatic tool every 300 work

hours or every 6 months.

When the pneumatic tool's hose is damaged, it must be

replaced with a specially prepared hose, available from

your FEIN customer service agent.

If required, you can change the following parts yourself:

Application tools, Hose

Warranty and liability.

The warranty for the product is valid in accordance with

the legal regulations in the country where it is marketed.

In addition, FEIN also provides a guarantee in accordance

with the FEIN manufacturer’s warranty declaration.

The delivery scope of your pneumatic tool may include

only a part of the accessories described or shown in this

instruction manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product

conforming with the documents and standards given on

the last page of this Instruction Manual.

Environmental protection, disposal.

Packaging, worn out pneumatic tools and accessories

should be sorted for environment-friendly recycling.

Vibration

Classification of FEIN

application tools according

to vibration class

Weighted acceleration*

VC0 < 2.5 m/s

VC1 < 5 m/s

VC2 < 7 m/s

VC3 < 10 m/s

VC4 < 15 m/s

VC5 > 15 m/s

3 41 01 101 06 0.book Seite 12 Freitag, 4. April 2008 8:33 08

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fein MOtlx 6-25 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info