Bedienungsanleitung Fein MShy664-1 (Seite 21 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

502247

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

The declared vibration emission level represents the

main applications of the tool. However if the tool is used

for different applications, with different accessories or

poorly maintained, the vibration emission may differ.

This may significantly increase the exposure level over

the total working period.

An estimation of the level of exposure to vibration

should also take into account the times when the tool is

switched off or when it is running but not actually doing

the job. This may significantly reduce the exposure level

over the total working period.

Identify additional safety measures to protect the opera-

tor from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation

of work patterns.

The vibrational emission values are given for dry grinding of

metal with grinding wheels. Other applications, such as belt

sanding, can lead to other vibrational emission values.

Handling hazardous dusts

For work procedures with this power tool where mate-

rial is removed, dusts develop that can be hazardous to

one’s health.

Contact with or inhaling some dust types, e. g. asbestos

and asbestos-containing materials, lead-containing coat-

ings, metal, some wood types, minerals, silicate particles

from materials containing stone, paint solvents, wood

preservatives, and antifouling paints for vessels, can trig-

ger allergic reactions to the operator or bystanders and/

or lead to respiratory infections, cancer, birth defects or

other reproductive harm. The risk from inhaling dusts

depends on the exposition. Use dust extraction matched

appropriately for the developing dust, as well as personal

protective equipment and provide for good ventilation of

the workplace. Leave the processing of asbestos-contain-

ing materials to specialists.

Wood and light-metal dust, hot mixtures of sanding dust

and chemical materials can self-ignite under unfavourable

conditions or cause an explosion. Avoid sparking in the

direction of the dust collector as well as overheating of

the power tool and the materials being sanded, empty

the dust collector/container in time, observe the material

manufacturer’s working instructions, as well as the rele-

vant regulations in your country for the materials being

worked.

Operating instructions.

Take care that the inner flange is mounted firmly on the

output spindle and that the centering sleeve is mounted.

Make sure to check that the grinding accessory is wider

than the height of the centering sleeve. Pay attention that

the grinding accessory is properly centred between the

inner flange and the threaded flange.

Using the same pressure, move the power tool back-

wards and forwards across the surface of the work piece

to prevent it from becoming too hot.

Motor protection switch MShy664-1 (see page 6).

If given, the motor protection switch switches off the

power tool in case of overload. After approx. 30 seconds

upon actuation, the electronic system can be reset via

button (a).

Do not actuate button (a) until after having released the

power tool’s switch.

Repair and customer service.

When working metal under extreme operat-

ing conditions, it is possible for conductive

dust to settle in the interior of the power

tool. The total insulation of the power tool can be

impaired. Blow out the interior of the power tool via the

ventilation slots frequently with dry and oil-free com-

pressed air, and connect a residual current device (RCD)

on the line side.

If the supply cord of this power tool is damaged it must

be replaced by a specially prepared cord available

through the FEIN customer service centre.

If required, you can change the following parts yourself:

Application tools, Threaded flange, Inner flange, Center-

ing sleeve.

Warranty and liability.

The warranty for the product is valid in accordance with

the legal regulations in the country where it is marketed.

In addition, FEIN also provides a guarantee in accordance

with the FEIN manufacturer’s warranty declaration.

The delivery scope of your power tool may include only

a part of the accessories described or shown in this

instruction manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product

conforming with the relevant provisions given on the last

page of this Instruction Manual.

Environmental protection, disposal.

Packaging, worn out power tools and accessories should

be sorted for environment-friendly recycling.

Selection of accessories

(see pages 11 – 12).

Use only original FEIN accessories. The accessories must

be intended for the power tool type.

A Wheel guard

B Inner flange

C Holding rod

D Centering sleeve

E Double-sided conical grinding disc

F Abrasive fleece wheel

G Threaded flange

H Small contact belt sander, sanding width 50 mm

I Contact disc, 50 mm

J Linen sanding belt, 50 mm width

K Small contact belt sander, sanding width 30 mm

L Special inner flange for small contact belt sander with

30 mm sanding width

M Contact disc, 30 mm width

N Special outer flange for small contact belt sander

with 30 mm sanding width

O Hexagon nut

P Linen sanding belt, 30 mm width

3 41 01 079 06 0.book Seite 21 Montag, 15. März 2010 11:24 11

Fein MShy664-1 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info