Bedienungsanleitung Fein STS325R (Seite 17 von 162) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

577151

Zoom out

Zoom in

Vorherige Seite

1/162

Nächste Seite

As an alternative, cutting paste can also be applied to the

cutting line.

When uncoupling hose couplings, first shut the ball valve,

then actuate the pneumatic tool, and then uncouple. Do

not uncouple the hose coupling until after the com-

pressed air has been completely relieved.

Using the recommended clamping

devices.

Clamping fixture 9 07 02 001 00 1

For pipes with diameters to 150 mm, use the clamping

fixture 90702001001.

– Place the clamping chain around the work piece and

insert the hooks of the grabber in the clamping chain.

– Tension the chain with the clamping-fixture handle.

– Mount the hacksaw to the retaining bolt (see “Mount-

ing the clamping fixture”).

The clamping head is readjustable for saw cuts and can be

used for angle cuts.

Clamping fixture 9 07 02 004 00 6

For large pipes with diameters from 150 mm to 325 mm,

use the clamping fixture 9 07 02 004 00 6 as well as saw

blades with lengths of 500 mm or 600 mm, and a thick-

ness of 2 mm. With the extension chain

3 02 31 003 00 3 (bolts 3 02 16 130 00 4), pipes with

diameters to 440 mm can also be cut.

Clamping fixture 9 06 06 002 00 9

When cutting pipes with diameters to 325 mm with the

1.6 mm thick and 530 mm long saw blade, use the saw

blade guide 90606002009.

– With the auxiliary handle removed, mount the saw

blade guide to the mounting hole of the pneumatic

tool’s gear head.

Clamping fixture 9 07 02 003 00 8

To cut profiled sections to a width of 290 mm and a

height of 550 mm, use the clamping fixture

9 07 02 003 00 8. Its design corresponds to that of a par-

allel vice. The clamping jaws and the clamping head are

adjustable.

Clamping fixture 9 07 02 005 00 0

When cutting pipes and round stock with outside diam-

eters from 80 to 400 mm, use the clamp and feed device

90702005000 to guide the hacksaw. A safety clutch

limits the duration that the saw blade is engaged and thus

increases tool life. For proper handling, please refer to

Instruction Manual 3 41 00 898 06 6.

Support for free hand working 3 27 14 062 02 3

To saw materials such as corrugated sheet, use the sup-

port for free hand working 3 27 14 062 02 3.

Remove the auxiliary handle and mount the support for

free hand working to the hacksaw via the clamping head

and the two gear head mounting holes for the auxiliary

handle. The saw blade goes through the opening.

Repair and customer service.

Carry out the following steps once per week:

– Pour a small quantity of petroleum directly into the

air intake of the pneumatic tool.

– Start the pneumatic tool for 10 to 15 seconds. In this

period, the petroleum will seep out of the pneumatic

tool along with the accumulated debris.

– Adding a small quantity of oil into the air intake after

the cleaning will benefit the performance of the

motor.

Further lubrication is covered by the oiler installed in the

handle.

Maintain and clean the pneumatic tool every 300 work

hours or every 6 months.

When the pneumatic tool’s hose is damaged, it must be

replaced with a specially prepared hose, available from

your FEIN customer service agent.

The spare parts list can be found on the Internet under

www.fein.com.

If required, you can change the following parts yourself:

Auxiliary handle, application tools, hose

Warranty and liability.

The warranty for the product is valid in accordance with

the legal regulations in the country where it is marketed.

In addition, FEIN also provides a guarantee in accordance

with the FEIN manufacturer’s warranty declaration.

The delivery scope of your pneumatic tool may include

only a part of the accessories described or shown in this

instruction manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product

conforming with the relevant provisions given on the last

page of this Instruction Manual.

Technical documents at: C. & E. FEIN GmbH, C-DB_IA,

D-73529 Schwäbisch Gmünd

Environmental protection, disposal.

Packaging, worn out pneumatic tools and accessories

should be sorted for environment-friendly recycling.

OBJ_BUCH-0000000098-001.book Page 17 Wednesday, March 6, 2013 1:56 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fein STS325R Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info