Bedienungsanleitung Fein wss 14 125 (Seite 22 von 195) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

391274

Zoom out

Zoom in

Vorherige Seite

1/195

Nächste Seite

For your safety.

Read all safety warnings and all

instructions. Failure to follow the

warnings and instructions may result in electric shock,

fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-

oughly read and completely understood this

Instruction Manual and the enclosed “General

Safety Instructions” (document number

3 41 30 054 06 1). The documents mentioned should be

kept for later use and enclosed with the power tool,

should it be passed on or sold.

Please also observe the relevant national industrial safety

regulations.

Intended use of the power tool:

Hand-guided angle grinder for dry grinding/roughing and

cutting of metal and stone in weather-protected environ-

ments with the application tools and accessories recom-

mended by FEIN.

This power tool is also suitable for use with AC genera-

tors with sufficient power output that correspond to the

Standard ISO 8528, design type G2. This Standard is par-

ticularly not complied with when the so-called distortion

factor exceeds 10 %. When in doubt, please refer to the

generator instruction/specification guide.

Safety Warnings common for Grinding, Sanding,

Wire Brushing or Abrasive Cutting Off Operations

This power tool is intended to function as a grinder,

sander, wire brush or cut-off tool. Read all safety warn-

ings, instructions, illustrations and specifications pro-

vided with this power tool. Failure to follow all

instructions listed below may result in electric shock, fire

and/or serious injury.

Operations such as polishing are not recommended to be

performed with this power tool. Operations for which the

power tool was not designed may create a hazard and

cause personal injury.

Do not use accessories which are not specifically

designed and recommended by the tool manufacturer.

Just because the accessory can be attached to your power

tool, it does not assure safe operation.

The rated speed of the accessory must be at least equal

to the maximum speed marked on the power tool. Acces-

sories running faster than their rated speed can break and

fly apart.

The outside diameter and the thickness of your accessory

must be within the capacity rating of your power tool.

Incorrectly sized accessories cannot be adequately

guarded or controlled.

The arbor size of wheels, flanges, backing pads or any

other accessory must properly fit the spindle of the power

tool. Accessories with arbor holes that do not match the

mounting hardware of the power tool will run out of bal-

ance, vibrate excessively and may cause loss of control.

Do not use a damaged accessory. Before each use inspect

the accessory such as abrasive wheels for chips and

cracks, backing pad for cracks, tear or excess wear, wire

brush for loose or cracked wires. If power tool or acces-

sory is dropped, inspect for damage or install an undam-

aged accessory. After inspecting and installing an

accessory, position yourself and bystanders away from

the plane of the rotating accessory and run the power

tool at maximum no-load speed for one minute. Damaged

accessories will normally break apart during this testtime.

Wear personal protective equipment. Depending on appli-

cation, use face shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing protectors,

gloves and workshop apron capable of stopping small

abrasive or workpiece fragments. The eye protection

must be capable of stopping flying debris generated by

various operations. The dust mask or respirator must be

capable of filtrating particles generated by your opera-

tion. Prolonged exposure to high intensity noise may

cause hearing loss.

Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal pro-

tective equipment. Fragments of workpiece or of a bro-

ken accessory may fly away and cause injury beyond

immediate area of operation.

Hold the power tool by insulated gripping surfaces only,

when performing an operation where the cutting acces-

sory may contact hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

dB dB Sound power level

pCpeak

dB dB Peak sound pressure level

K... Uncertainty

m/s

Vibrational emission value according to EN 60745

(vector sum of three directions)

h,AG

m/s

Mean vibrational value for angle grinding

h,DS

m/s

Mean vibrational value for sanding with sanding

sheet

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

min, m/s

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

min, m/s

Basic and derived units of measure from the inter-

national system of units SI.

Character Unit of measure,

international

Unit of measure,

national

Explanation

WARNING

OBJ_BUCH-0000000034-001.book Page 22 Monday, May 9, 2011 12:44 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fein wss 14 125 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info