Bedienungsanleitung Felisatti DCHF 13 (Seite 5 von 32) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

500410

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

been charged 100% and is ready for use.

4. Once the charge is completed and the red color led J is

lit up, the charger will maintain and balance the charge level

in the different battery cells so it is always ready and available

for use.

Respect the charge time indicated in the table.

Warning! Before charging a battery that has recently been in

use or exposed to direct sunlight or heat, leave it to cool. This

will enable it to be fully recharged.

DISCHARGE OF THE BATTERY

Once the battery is fully charged, the drill may be used again.

Try not to discharge the battery completely.

ACCESSORIES

Accessories and their corresponding order number can be

found in our catalogues.

MAINTENANCE AND CARE

Remove the battery before carrying out any operation on the

machine.

- Clean the machine very carefully after each use. The air

vents should always be kept clear.

- Store in a dry place, away from cold .

- Use only Felisatti accessories and spares. These should

be tted in a Felisatti technical service centre (See Warranty/

Technical Service Centre address leaet).

- Brush replacement: The brushes disconnect auto-

matically and should be replaced after 80 - 100 hours use

or when they are less than 3 mm long. Have them replaced

by an Ofcial Service Centre. We recommend that at every

second change of brushes, you take the machine to one of

our Ofcial Service Centres for general cleaning and oiling.

WARRANTY

See general warranty conditions printed on the attached

sheet.

• Low speed (1) (lever forwards) for screwdriver action

and drilling ceramics and for starting to drill brick without a

piercer.

• High speed (2) (lever backwards) for drilling brick (in

hammer mode), for drilling wood and derivatives, plastics

and metals.

The speed can be adjusted while the machine is running.

However, this should not be done at full load. If, when the

machine is stopped, the selector C cannot be set in its nal

position, push the on/off E switch briey.

4. Attachment of bits in the keyless drill chuck (Fig. 1)

1. Open the drill chuck A and insert the drill bit or screwdriver

bit (in clamp H).

2. To block the bit or screwdriver tip, turn the drill chuck in

a clockwise direction, looking at the machine from the front.

5. Torque adjustment (Fig. 1)

• For use as a screwdriver, the drill-screwdriver is equipped

with an adjustable clutch, operated by the torque adjustment

control B which has 21 settings. Once it has been correctly

adjusted, the friction clutch is released when the preselected

torque setting is reached, to avoid the screw penetrating too

far or damage to the machine. Adjustment depends on the

type and size of the screw used. It is advisable to always

begin in the lowest setting (1) and increase gradually until the

desired result is obtained.

• For use as a drill, set the torque adjustment control B to

the drill setting. The clutch is designed not to work in the drill

mode.

6. Hammer control (Fig. 1)

• Hammer drill

Turn the torque adjustment screw B until the hammer gure

coincides with reference arrow.

To drill brick and similar materials, adjust the machine to

hammer drill mode. The bit hammers the material while it

turns.

When using the machine continually in hammer mode, it may

become hot. If this happens, leave it to cool. If the motor

blocks, unplug the machine immediately.

WARNING! When working in hammer mode, ensure the

machine turns in a clockwise direction!

• Drilling without hammer

Turn the torque adjustment screw B until the drill bit gure

coincides with reference arrow S.

• Screwdriver action

Adjust the torque adjustment screw B to the appropri-ate

position from 1 to 21 as described in the section covering

tightening torque adjustment.

CHARGING THE BATTERY (Fig. 2)

To remove the battery F from the machine, press both side

buttons, G, situated on the handle, at the same time.

To charge the battery with a quick 60 minute charger, proceed

as follows:

1. Place the battery charger I on a at surface and plug the

charger into the mains.

2. Fit the battery F upside down into the charger. Ensure

that the battery tab is aligned with the inner slot on the

charger. Check that the terminals + and – of the battery and

the charger coincide. After putting the battery in the charger,

you will observe that the red color led J will ash as an

indicator that the battery is charging.

Note: If the ashing frequency of the red color led J is

very fast, or is not constant, it is an indicator that the battery

is in poor condition and should be replaced.

3. Once the battery charge is completed, the red color led

J of the charger I will remain permanently lit. The battery has

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Felisatti DCHF 13 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info