Bedienungsanleitung Felisatti NTF250 (Seite 7 von 52) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

502511

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Model NTF250/1200ST NTF305/1600ST

Tension and current V / A 230V-5,5A 230V-8A

Frequency Hz 50 50

Absorbed power W 1200 1600

Idling speed /min 4500 4000

Cut at 90°/crop (AxB g. 3) mm 73x150 102x150

Cut at 45°/crop (AxB g. 4) mm 73x90 97x102

Cut at 45°/blade at 45° (AxB g. 6) mm 46x150 66x150

Cut at 45°/blade at 45° (AxB g. 6) mm 45x48 45x53

Cut on upper table mm 40 66

Upper table dimensions mm 473x312 473x312

Blade diameter mm 250 305

Blade hole diameter mm 30 30

Weight kg 22 25

Overall dimensions (LxHxW) mm 520x396x650 573x432x667

Sound pressure emitted Lpa dB(A).(*) 91 96

Sound power emitted Lwa dB(A).(*) 104 109

Vibration level m/s2 (*) 1,0 (<2,5) 0,7 (<2,5)

* Reliefes enforced by the standard: EN 61029

2.2 STANDARD ACCESSORIES

This series of mitre saws is supplied complete with

the following set of standard accessories:

Adjusting rod (g. 7): required for the cutting of beams

of the same length.

Pusher For the working of small parts on the upper

table (g. 20).

Blister pack of Allen wrenches.

Important: the equipment provided may vary

according to the sales campaign in progress.

2.3 ACCESSORIES AVAILABLE ON REQUEST

The following accessories for particular work

conditions are also available on request:

Rapid clamp: (g. 8) permits the tighter locking of

bars and sections without vibration.

Foldable and movable universal support for mitre

saws (A g. 19).

Support and roller unit (B g. 19) for jutting piece

Vacuum unit (C g. 19) with connection tube and

spout.

Goniometer: to make angled cuts on the upper

table

(g. 21).

Workpiece support stroke-end raised section (G

g.1

WARNING! The use of accessories or attachments

other than those recommended in this manual may

pose risk of injury.

2.4 SAFETY DEVICES

In rest position, the blade is completely protected

by two xed casings and one movable casing with

opening that is automatically triggered by the lowering

of the blade unit during the execution of the cut.

On the upper table, the blade is protected by a casing

that is raised over the workpiece as it approaches the

cutting point.

WARNING! Never remove these protective casings

that enable the operator to work in conditions of

safety.

WARNING!

CHECK ALL DAMAGED PARTS

• All the parts of the tool should be carefully checked

before use in order to make sure that they will work

correctly for the operation foreseen.

• Check the alignment and assembly of all moving

parts for signs of breakage and any other conditions

that might compromise operation.

• Damaged protective casings and/or other parts

should be replaced by an authorised service center

unless indicated otherwise in this manual.

• Have defective switches replaced by an authorised

service center.

If the LOCK in “ON” button has not been pressed,

the blade automatically stops when the starting

lever switch in the handgrip is released.

WARNING!

Pressing the LOCK in “ON” button disables the safety

feature provided by the Manufacturer in the starting

2.1 TECHNICAL DATA

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Felisatti NTF250 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info