Bedienungsanleitung Felisatti NTF250 (Seite 11 von 52) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

502511

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

WIDIA BLADES MATERIAL BLADE Ø – No. TEETH /min

WOOD

Ø 250 mm - Z 24 4500

Ø 250 mm - Z 40 4500

Ø 250 mm - Z 60 4500

Ø 305 mm - Z 72 4000

PVC Ø 250 mm - Z 60 4500

ALUMINIUM

Ø 250 mm - Z 60 4500

Ø 305 mm - Z 72 4000

FRAMES Ø 250 mm - Z 80 4500

does not provide shorter cutting times and can lead

to diminished efciency caused by the overloading of

the motor.

6.4.1 STARTING AND STOPPING THE BLADE

- Start the blade by pressing the tool lever A (g. 2)

and then wait until the blade reaches its maximum

rpm. - Lower the blade unit gradually and then

make the cut desired. After the cut has been made,

release the lever A (g. 2) and then wait until the

blade has come to a complete stop.

WARNING - Make sure that the movable protective

casings are all in correct position whenever the blade

is raised in rest position. The machine is provided

with a release button for the starting and stopping

of the blade. This button can be locked in “ON” by

pressing the switch black key B when the switch

black lever A is at the end of its stroke and the motor

is running (g. 2).

WARNING - This Lock in ”ON” button disables the

safety provided by the Manufacturer in the starting

lever switch. We recommend using this device only

with the greatest caution and only when the tool is

being used as a disk saw. In order to release the

switch, press the black lever A and then release it.

6.5 USING THE STROKE END RODS (g. 7)

Proceed as follows to use the stroke end rods: - Insert

the rod A in the hole of the workpiece support and lock

it in place with the corresponding knob B – Loosen

the knob C and adjust the rod D as required by the

length of the workpieces by using the millimetre ruler

for reference. Then lock the knob C back into position.

6.6 USING THE CLAMP (g. 8)

Proceed as follows to use the clamp:

- Insert the pin A in the corresponding slot B and lock

it in place with the dowel C located in the rear part of

the workpiece support

– Insert the clamp D on the pin A and lock it in place

at the desired height using the wing nut E

– Lock the piece to be cut into place by tightening

the upper knob F.

6.7 USING THE UPPER TABLE AS A DISK SAW

WARNING - The use of the upper table for the cutting

of steel and aluminium is absolutely prohibited.

- Never use the tool to make slots.

Proceed as follows to use the upper table: - Make

sure that the switch is not locked in “ON” - Completely

lower the blade unit and lock it in place using the pin

F (g. 1)

(RI and NTF305 version)

– This version is equipped with ne-adjustment:

adjust the height of the upper table using the knob N

(g. 1) and then lock the table in position by tightening

the knob S (g. 1).

(RP version)

- Adjust the height of the upper table as required by

the piece to be cut, and then lock in position using the

corresponding knobs S (g. 1) and T (g.9).

6.7.1 STARTING AND STOPPING THE BLADE

- Start the blade by pressing the tool lever A (g. 2)

and then press the black key B (g. 2) and wait until

the blade reaches its maximum rpm. - Make the cut

desired.

After the cut has been made, press the lever A (g. 2)

and then release it and wait until the blade has come

to a complete stop.

6.8 USING THE STROKE-END GUIDE FOR THE

UPPER TABLE (g. 9)

Proceed as follows: - Insert the guide G (g. 9) in the

upper table – Select the desired cutting width using the

graduated scales – Lock into the guide G into position

using the knob H.

6.9 CUTTING SMALL PIECES

Small pieces must be worked with the use of the correct

tools – On the lower table: Use the clamp to lock the

workpiece in place and the stroke-end rods to obtain the

size desired – On the upper table: Use the pusher (g.

20) provided to advance the workpiece.

Never put your hands on the workpiece to be cut.

Keep the pusher in a safe place nearby for use

whenever required.

6.10 CUTTING LARGE PIECES

Never remove the workpieces that have already been

cut or other parts of the workpieces to be cut while the

machine is working and the support is not in rest position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Felisatti NTF250 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info