Bedienungsanleitung Felisatti NTF305 (Seite 9 von 52) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

502512

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts and

any other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc., in accordance with these instructions and in

the manner intended for the particular type of power

tool, taking into account the working conditions and

the work to be performed. Use of the power tool for

operations different from intended could result in a

hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualied repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

4 INSTALLATION

4.1 PACKING AND UNPACKING

The mitre saw, complete with its accessories and

instructions for use ts inside a package and is locked

in position for transport.

WARNING! During transport the upper of the blade

must be covered by the upper protection or set in its

lowest position.

WARNING! Before using the tool, release the knob A

and the respective self-locking nut (g.12) previously

locked in position for the transport of the mitre saw

(see also Point 5.2).

4.2 LIFTING

The mitre saw must be lifted using the equipment and

safety measures adequate for the operation. The

mitre saw can be moved manually, provided that at

least 2 people are assigned to the task. Install the

mitre saw on a solid and sufciently level surface at

the ergonomically correct working height.

WARNING! Never lift the machine up by its protective

casings.

4.3 INSTALLATION

Room conditions, such as temperature, humidity,

illumination, general cleanliness and the correct

position of the mitre saw are all very important for

the safety of the operators and the performance of

the mitre saw itself. Also make sure that the tool is

securely fastened to the work bench.

4.4 ELECTRIC CONNECTION

Before connecting the machine to the power mains,

make sure that the electric system corresponds to the

regulations in force in the nation of use (with the

presence of a ground system, thermal cutout,

overload cutout) and that the voltage and frequency

correspond to the indications provided on Plate A (g.

1). Before using any extension cables, make sure that

the section of the cable is adequate to its length and

that a grounding connection is provided. Whenever

coiled extension cables are used, make sure that

they are completely uncoiled in order to prevent the

risk of overheating.

WARNING! The starting switch on these tools is

provided with a LOCK in “ON” button that permits

prolonged use (only when the tool is used as a

disk saw, however) without requiring the starting

switch to be pressed constantly. Before plugging

the tool plug into the socket, make sure that the

starting switch is set in the unlocked position.

Whenever the tool will not be used for some time,

always remember to switch it off and leave the

lever in released position.

4.5 WORK PLACE

The tool that you have purchased is a movable power

tool that requires only one operator for use thanks

to its conformation, weight, and handiness. Under

conditions of normal use, the operator standing in

front of the machine has the handgrip in front of him.

5 REGULATION – MITRE SAW SQUARING

The mitre saw is delivered by the Manufacturer

after regulation and squaring performed to standard

parameters.

Squaring can be adjusted whenever required (see

Points 5.4 - 5.7).

WARNING - Always unplug the plug from the socket

before proceeding to any regulation operations on the

mitre saw.

5.1 BLADE UNIT LIFTING

An assembly of internal springs keeps the blade unit

raised in rest position. In this position, a safety catch

prevents the accidental operation of the blade unit.

5.1.1 In order to release the blade unit and permit the

use of the machine as a mitre saw, press the orange

key C on the handgrip (g. 2) (this operation can be

performed by keeping your right hand steady on the

handgrip).

5.1.2 In order to use the machine as a disk saw,

release the blade unit as shown in 5.1.1, and after

lowering the unit completely, lock it in place with the

pin F (g. 1). In this position, the oscillation of the blade

unit can be reduced by using the knob A (g. 12).

Remember to return the knob to its original position

whenever the machine must be used as a mitre saw

(unscrew up to the position dened by the self-locking

nut).

5.2 BLADE PENETRATION DEPTH REGULATION

(g. 12)

The blade penetration depth has already been set by

the Manufacturer during nal testing. Due to the

fact that incorrect regulation prematurely dulls blade

sharpness and/or may break blade teeth, additional

regulation might be required by proceeding as follows:

- Turn the knob A and the respective self-locking

nut in order to set a limit on the descent of the motor

Felisatti NTF305 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info