Bedienungsanleitung Felisatti PF110 (Seite 4 von 24) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

502501

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

surface.

For surface planing a shallow cutting depth is recommended,

repeating the process several times.

3. Canting off edges

Guide slot P, located in the centre of mobile plate S, enables

fast, simple edge canting off to be carried out on the work-

piece.

The plane should be placed with guide slot P over the edge

of the work-piece and then guided along its length. A constant

angle of 45º should be maintained during this operation,

together with a uniform advance movement.

4. Carrying out routing and bevelling

- Depth limit N

The assembling must take place at the right side and the

depth reduction may be adjusted from 0 to 15mm.

In order to enable the reduction, it is important that the blade

should be ranged well sideways with the side level of the

mobile and xed bases.

- Side limit L

The side limit L may be adjusted at both sides of the plane,

keeping it immovable by means of the control I.

In order to assemble the lateral stop, rst place the set square

V and x it with wing nut I (Fig. 1).

Place the lateral stop L, put the nut on the hexagonal slot

of the upper part of set square V and x it with wing nut W

(Fig. 1).

In order to disassemble the lateral stop, follow the instruction

in a reverse order.

In order to adjust the lateral stop, loosen wing nut W, move

the side stop in order to achieve the desired measurement

and again tighten wing nut W.

Using depth end-stop N together with side end-stop L permits

routing operations.

PARTS REPLACEMENT

1. Blade replacement (Figs. 6)

WARNING! Only hard metal blades may be used with this

tool.

It is tted with hard metal blades when it leaves the factory

. When blade replacement becomes necessary, both should

be replaced at the same time. Otherwise, the lack of balance

could lead to vibration reducing the lifetime of the tool.

The blades of hard metal have two rows of edges and may be

converted or changed without having to be adjusted. In order

to convert or change the blades, just screw off by one or two

turns the screws O and with a pointed piece of wood, take out

sideways the blade.

Before reassembling again the blade, clean the carrier or

guide of the blade, making sure the carving of the blade and

the guide rule t correctly.

Adjust the lateral position of the blade to the level of the xed

and mobile bases by means of a wooden strip, Fig. 6.

Tighten again the three screws O.

PRECAUTION: Jagged or worn blades cannot be

resharpened and must be replaced.

2. Toothed belt replacement (Fig. 5)

The procedure for replacing the toothed belt is described

below:

1. Loosen screw R and remove toothed belt cover Q.

2. Cut the toothed belt with shears or a knife and remove it.

3. Before installing a new toothed belt, thoroughly clean

pulley G and drive wheel E.

4. Install the new toothed belt on drive wheel E and press it in

place, while rotating large pulley G at the same time.

5. Replace toothed belt cover Q and x it in place with screw

DUST EXTRACTION

WARNING! Always check that the machine is switched off

and unplugged before removing or installing any dust and

sawdust suction device.

Dust extraction keeps the workplace clean, prevents dust

build-up in the air and facilitates waste elimination.

These plane have a chip expulsion hole M to which adapter T

may be connected. A universal vacuum cleaner may be tted

or any dust extraction device.

PRECAUTION! During prolonged operations with wood or in

professional applications with materials that produce harmful

dust, a suitable external aspirator must be connected.

ACCESSORIES

Accessories and their corresponding order number can be

found in our catalogues.

MAINTENANCE AND CARE

WARNING! Always unplug the machine before carrying out

work on it.

- Blade inspection: Excessive forward movement will

signicantly reduce machine power and blade life. Sharp

blades will permit a high cutting capability and increase

machine life. Blades should be replaced according to

requirements.

- Inspect the mounting screws: regularly inspect all the

mounting screws and ensure they are rmly tightened.

Should any screw be loose, tighten it immediately. Failure to

do so could put you at serious risk.

- Motor maintenance: always take the greatest care over

this and make sure that the motor winding is not damaged

and does not become wet with oil or water.

- The vents should always be kept clean and free of

obstacles.

- Clean the machine thoroughly after each use. Blast the

motor regularly with compressed air.

- Check that the mains lead is in good condition. If it is not,

take it to an Ofcial Service Centre to have it replaced.

- Brush replacement: brushes must be replaced when length

reaches 8 mm or less. To do so, please contact an authorized

after sales service centre. We recommend that every other

time you take a tool to an after sales service centre for carbon

brushes replacement you also order a general maintenance

(cleaning and lubrication).

- Use only Felisatti accessories and spares. Parts the

changing of which is not covered in this instruction manual,

should be replaced in a Ofcial Service Centre (See Warranty/

Ofcial Service Centre address leaet).

Felisatti PF110 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info