502470
4
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
4
Follow very carefully the instructions in this manual, save it
and keep close at hand, ready to carry out any inspection of
parts that may be necessary.
If the machine is used carefully and normal maintenance is
carried out, it will work well for a long time.
The functions and use of the tool you have bought shall be
only those described in this manual. Any other use of the tool
is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See gures)
A SDS-plus chuck (Fig.1)
B Chuck sliding ring (Fig.1)
C Speed regulating handwheel (Fig.1)
D Push button for mode change (Fig.1)
E Mode changeover(Fig.1)
F Label for reversing rotation R-L (Fig.1)
G Changeover left/right direction switch (Fig.1)
H On-/off switch (Fig.1)
I Locking button (Fig.1)
K Depth stop xing wing nut (Fig.1)
L Depth gauge (Fig.1)
M Auxiliary handle (Fig.1)
N Screwdriver bit (accessory*) (Fig.2)
O Key chuck (accessory*) (Fig.2)
P SDS-plus adapter (accessory*) (Fig.2)
* Not included in standard equipment, available as an
accessory
BRIEF DESCRIPTION
A percussion unit generates the power necessary for hammer
drilling or chiselling in masonry.
Just like when we hit a conventional chisel with hammer, a free
piston strikes the bit or chisel, which can move lengthways,
through an intermediate part. This free piston is driven by
a second piston activated by an electric motor through an
air cushion. This electro-pneumatic principle offers great
percussion elasticity and work free from recoil.
Unlike a normal hammer drill, the drilling capacity does not
depend on the pressure exerted on the machine.
Use of the tool: The rotary hammer can be used for hammer
drilling and drilling in wood, metal as well as plastic, and also
for driving screws with driving bits installed in a key chuck
with the SDS-plus adapter. Any other use not mentioned is
TECHNICAL DATA
not allowed.
Additional features of the rotary hammer:
- The machine is equipped with a safety clutch or mechanism
which operates when a bit seizes up, pro-tecting the user
and the machine’s electro-mechanical parts. The clutch is
released automatically.
Warning! This machine must not be used with hole saws, core
bits, diamond bits, etc, as they tend to jam in the hole easily.
This would cause the safety clutch to trip out too often.
- Percussion drill chuck A with SDS–plus mounting for using
tools with SDS-plus shaft. A geared drill chuck or a keyless
chuck can be used in conjunction with the SDS-Plus Adapter
P.
- Change direction of rotation with switch lever G –due to a
lockout mechanism, switching the lever is only possi-ble if the
On/off switch H is not depressed.
- Electronic control of spindle speed, innitely variable by
nger pressure on the On/off switch H.
- For maximum speed regulation use handwheel C.
- For continuous operation the On-/Off switch can be locked
in the “On” position by the button I.
- Auxiliary handle M, adjustable, with integral depth gauge L.
BEFORE USING THIS TOOL
WARNING! Before carrying out any work, check, for instance,
using a metal detector, that there are no electric wires or gas
or water pipes under the surfaces you wish to work on.
Make sure the mains voltage is correct: it must be the same
as that on the specication label. Machines with 230V can
also be connected to a 220-V mains supply.
To turn the machine on, press the ON/OFF switch H and keep
it pressed down.
When the ON/OFF switch is released, the machine stops.
WARNING! Always disconnect the plug from the socket
before doing any work on the machine.
1. Fitting the working tools
Hammer drill (Fig.1)
Only use tools with SDS-plus shaft!
1. Clean and grease the shaft of the tool.
2. Before inserting the tool, move the sliding ring B back.
Now the SDS-plus chuck is open.
3. Push the tool in, turn it slightly until it can be pushed in
all the way and you can feel it notch into place.
4. Release the sliding ring B. Now the tool is locked.
5. Check that the tool is properly locked into place. It must
be possible to move it about 10 mm lengthways.
6. Switch machine over to hammer drilling with lever E in
appropriate position.
SDS-plus adapter for geared drill chuck (Fig.3)
Rotary hammer RHF 18/450ERT RHF 22/620ERT
Rated power
W 450 620
No load speed
/min 0-1650 0-1100
No load hammer rate
min 0-7500 0-5060
Drilling diameter in concrete
mm 18 22
Drilling diameter in steel
mm 13 13
Drilling diameter in wood
mm 24 30
Weight according EPTA-Procedure 01/2003 kg 2,1 2,5
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Felisatti RHF18 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info